Returning to std springs

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
All
I agree it’s all down to taste, I’m not doing anything radical.
Over the years I’ve owned lots of different land rovers, range rovers, a disco and a few swb series.
This is a v8 auto 90. It was built by the previous owner from an 1990 Range Rover.
He did a nice job.
My plan is to take the roof off for the summer and have it a a toy to run round in.
Roof back on for the winter, might not get the roof off this year mind.
I m after a sort of updated NAS 90 look.
Just getting all the parts together.
Dave
 
lvdxd00 said:
All
I agree it’s all down to taste, I’m not doing anything radical.
Over the years I’ve owned lots of different land rovers, range rovers, a disco and a few swb series.
This is a v8 auto 90. It was built by the previous owner from an 1990 Range Rover.
He did a nice job.
My plan is to take the roof off for the summer and have it a a toy to run round in.
Roof back on for the winter, might not get the roof off this year mind.
I m after a sort of updated NAS 90 look.
Just getting all the parts together.
Dave
Click to expand...

V8 Auto Ninety is a very nice drive. You will enjoy that. :)
 
Turboman said:
V8 Auto Ninety is a very nice drive. You will enjoy that. :)
Click to expand...
It’s fun and loud.
Needs a bit of tlc.
Just in the process of fitting a stainless sports exhaust.
Moving the gear shifter to a better position.
It came with rx8 heater electric seats that need fitting.
Half way there with them.
Doors are shot so got some series doors to go on.
Found a military roll bar and hoops.
All jobs to do.
 
Got a few jobs done on my 90, been a long road and still near the start.
Seats in, very comfy. Exhaust done, what a faf, didn’t fit properly. A few mods to make it fit.
Disco2 shifter fitted.
Drivers door fitted, needs painting.
Today’s job was to swapping back to standard height springs from 2” lift springs, guess what stayed the same height.
Rear springs where definitely shorter than the old ones, but the front springs looked to be the same length.
Do you think it will settle ?
Dave
 
Last edited:
Interesting that You posted here. Just 30 min ago I was driving back home and thinking that I have to try the 2 inch lift after all. The curiosity is killing me.. All in the name of looks (fitting 285/75r16). Also planning to try the light load version from Terrafirma, despite all the criticism I've heard reading through the threads.

Hope someone will answer the question about Your rear springs. Can You by any chance post a photo from the side to see how noticeable is that difference in height?:)
 
You could have had softer springs fitted (than your replacements) even though they were 2" taller, or they might well just have been knackerd and sagging a bit.
There are loads of different spring ratings you can get, have you got the right ones anyway?
 
frog hopper said:
You could have had softer springs fitted (than your replacements) even though they were 2" taller, or they might well just have been knackerd and sagging a bit.
There are loads of different spring ratings you can get, have you got the right ones anyway?
Click to expand...
The springs that came off where terrafirma +2” and the ones that went on where bog standard.
Still looks lifted. Currently it has 235/85r16 tyres fitted. How big would the gap between the tyre and the arch be for standard. Ie no lift?
 
I doubt you'll find a standard measure. Body configuration and weight of the vehicle will impact this. And there have been loads of different "Standard" rate and length springs over the years.

Maybe post a picture of what it looks like now. Also, did you take any before and after measurements? Or pics of the springs side by side?
 
Have not got measurements but here is my standard TD5 XS. With 235.85.16s
20140323_142356.jpg
IMG_0693-1.jpg
 
Last edited:
lvdxd00 said:
Today’s job was to swapping back to standard height springs from 2” lift springs, guess what stayed the same height.
Click to expand...
Possibly the steering rods had to be adjusted to be longer when the lift was made, and maybe a longer prop shaft(s). Is it sitting up on the rods and shafts? (others will comment if this is crap as I never done a lift myself)
 
lvdxd00 said:
This an old photo, before I swapped the springs
[GALLERY=]View attachment 172851 [/GALLERY]
Click to expand...
Those tyres look small. What size are they and what height do they measure.

I can also see cranked rear arms and I suspect castor corrected front arms and non standard shocks. All of these things could easily impact the tyre to wheel arch clearance.

Front wheelarch also doesn't look level. Is the wing bent as well?
 
300bhp/ton said:
Those tyres look small. What size are they and what height do they measure.

I can also see cranked rear arms and I suspect castor corrected front arms and non standard shocks. All of these things could easily impact the tyre to wheel arch clearance.

Front wheelarch also doesn't look level. Is the wing bent as well?
Click to expand...

The front wing is a little bent.
The tyres are 235 85 16
The front control arms are standard ones, the rears are castor corrected. Going to get these replaced soon.
It does ride better on the new springs
The shocks are the ones terrafirma recommended for std suspension
 
Last edited:
You must log in or register to reply here.

Similar threads

MAF Diver
Disco 2 Do you need extended shocks for a 0.8 inch lift at the front? Air suspension in the back (SLS)
Replies
13
Views
1K
MAF Diver
MAF Diver
L
Mantec Swing Away Wheel Carrier Parts
Replies
0
Views
615
Lumby84
L
M
Warning to the unwary
Replies
7
Views
578
lynall
L
B
Returning to the fold
Replies
3
Views
562
brianp38dse
brianp38dse
J
D1 suspension - improve ride quality?
Replies
9
Views
953
Jalfrezi
J
Back
Top