davidsmith1307
Well-Known Member
- Posts
- 1,333
- Location
- Hull
You can't just leave it at that!
P38 thor 2002. I'm doing something stupid to the EAS
- Thread starter supapete
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
kurtjohnson10
Well-Known Member
- Posts
- 15,235
- Location
- midlands
are we still on about grrrrs budgie smugglers or petes eas ?
I'm waiting for the results before we comment on the fix.
I'm fairly sure that we have sussed out what's wrong but either pete or I will update once it's working.
supapete
Active Member
- Posts
- 505
- Location
- West wing I think
I can't tell a lie. It'll take a while of counseling and therapy to muster the courage to own up to what I've done. Luckily wazza didn't leave bruises that show. Now to face Matron.
kurtjohnson10
Well-Known Member
- Posts
- 15,235
- Location
- midlands
keep going!
by making mistakes sometimes the best learning points are found
by making mistakes sometimes the best learning points are found
kurtjohnson10
Well-Known Member
- Posts
- 15,235
- Location
- midlands
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Man up or I will tell her to give you a barbed wire enema
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
You crossed the pipes over?
supapete
Active Member
- Posts
- 505
- Location
- West wing I think
You've done it now. I've been moved to a safe house for my own protection.
- Posts
- 12,628
- Location
- Sud ouest France !
are the results in? Come on!!
supapete
Active Member
- Posts
- 505
- Location
- West wing I think
We'll, not quite. The definition of BLOCK is a solid hard object flat on all sides. My one remaining brain cell interpreted it as that. I wondered why the land rover ones were spindles. Hmmmmmm. By putting my 100mm blocks betwixt bump and axle plate the spring was already up to ninety nine. So, when I put it up to extended to get my blocks out one or more of the springs went west and turned into UXB s. My one remaining brain cell also told me as the bags were new, they must be OK so I blamed everything else. That doesn't mean that there weren't other faults. I think I've fluked 3 good bags and the one I haven't is on its way. My heading was that I'd done something stupid and I have. I've now made some SPINDLES which can be inserted into a flat timber receiver clearly marked with size/rear etc. I'm now in the process of lowering. It'll take a while because wazzas bruises and matron's barbed wire therapy are restricting my agility somewhat. Watch this space.
- Posts
- 12,628
- Location
- Sud ouest France !
are your shocks absolutley the correct ones? I recently fitted the terrafirma hd's, but not the 2" lift units, for obvious reasons. I used a good car jack to lift and lower mine onto the cal'blocks. I found that to be more reliable. Its sounds like tye shocks are allowing the bus to lift too high!! Is the pressure switch in working order?
supapete
Active Member
- Posts
- 505
- Location
- West wing I think
I've suspected the shocks all along but I was only guessing. I'm going with the pros this time. I've just used the jack method to lower the Ratbag onto my patent calibration pillars. I've done three levels now and as you intimate the rear end was slow to settle from high to STD. I could still turn the spacers for a while. My next step is to manipulate the front sensors to read 2 points difference or less. Then I'll report back to my guru. Watch this space.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Hint............ The measuring blocks go INSIDE the bump stops, not between the bump stops and axle.
He must have been able to see in first floor windows while driving.
supapete
Active Member
- Posts
- 505
- Location
- West wing I think
Here we go. I knew I was in for it....Btw, I put a new pressure switch on as a matter of course when I re O ringed the valve block. I've also bought a substitute valve block pre doctored. Got the sensor readings within 1 side to side. The threaded plug thing that the sensor fixings screw into had come adrift. Whatever stick I'm in for can't be worse than this. Watch this space.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
We're changing your nickname to Lofty.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
The man who hasn't made a mistake hasn't done anything '
'supapete
Active Member
- Posts
- 505
- Location
- West wing I think
I'm getting away light here. My rear airbags aren't showing their knickers and my side to side sensor readouts are parity and 1. As a temporary emergency get out of jail measure I've replaced all airbags with colanders which hold pressure longer. If this post appears less than communicable I'm suffering with altitude sickness. Say hello to our new forum........ girrafeyzone.
