neep help urgent

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
The Mad Hat Man said:
how easy to get to connectors on the Alt?
Click to expand...
Looks like access will be between the engine and radiator half way donw so not easy but must be do-able. Mix of above and below to get the best access. Never done a td4 before.

Several FL1 2002 onwards alternators on ebay local to where he is, if it needs replaced.
 
thanks for everones help

ive swopped bats and just setting off to try and get to penistone near sheffield

fingers crossed

will up date later

thanks everyone

griff
 
Access looks a bit tight. The air con compressor looks as if it's in the way if fitted. I've not got a td4 but I'd try not to have to remove the coolant if possible. Just makes it easier.

The rave disk tells you to disconnect the battery. Remove the engine sump guard. Drain the engine coolant. Remove the coolant hose at the lower front of the engine. Release the auxiliary belt. Undo the air con compressor bolts and move to one side (don't disconnect the air con pipes). Remove air con compressor mounting. Swap the alternator. Reverse to put back.
 
LZIR stood down.

notify me of any further requirements.

OP - reply to txt - if we dont know we can contact you - yu are helpless.

Cabbie just replied - ta
 
Just cought up on this... Only at Garforth maybe 5 miles from sherburn... Tools in motor if needed .. also have rigid tow bar and ropes straps if he don't make it home.. might even have a spare battery at home...

Finish work at 5 though so hopefully he will be home by then...
 
I'm not far from the M1, and I'm at home today, wouldn't be much use other than a tow or a lift though. You have my number
 
Fresh battery on a diesel driving at day time with no lights on he'll easily do 50 miles and then some. It's only powering the ECU and a few other bits...
 
thanks everybody

ive managed to get to my destiation :) (just)

ive got hold of a alt (110 amp)
but i have no tools,ramps etc with me :-(

looks like im going to have to buy some ,anyone have any idea what tools is needed???????

and best place to get them? as have no access to a car :-(

im in penistone,sheffield area

cheers
griff
 
Last edited by a moderator:
Guessing no news is good news at this point. Just back from rescuing landladies daughter who's blown the head gasket on her 406.
"It got really hot and the stop light came on but then the temp gauge went down again so I carried on...." :doh:
 
blue beasty said:
Guessing no news is good news at this point. Just back from rescuing landladies daughter who's blown the head gasket on her 406.
"It got really hot and the stop light came on but then the temp gauge went down again so I carried on...." :doh:
Click to expand...

He needs help in the form of tools and advice in the Sheffield area.

Makes perfect sense... it all broke, but, then, magically fixed itself so good to continue :p
 
Is it possible for someone to link the relevant part of RAVE so Griff can have a read up?

I'm not going to try a access the map because my phone batt is dying fast but if someone wants to have a look from the link in lzir section and list up peeps around Sheffield me or Daft can contact them
 
You must log in or register to reply here.

Similar threads

S
Newbie urgent help supercharged 55 reg problems
Replies
2
Views
536
Grrrrrr
Grrrrrr
Speedex750
Non standard alternator; problem diagnosis?
Replies
8
Views
1K
freelance
freelance
spacebrodie
Freelander 2 (LR2) Cut out - P0045-19
Replies
6
Views
657
Arctic2
Arctic2
Bustrucket
Disco 2 Td5 Overheating
Replies
3
Views
776
johnlad
johnlad
P
Freelander 1 code p1672 in 2023 - asking for help
Replies
1
Views
719
Dar ran Dar ran
Dar ran Dar ran
Back
Top