P38A Might have bought a camel.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
D

Duncanincapable

Active Member
Posts
99
Location
Barnoldswick lancashire
Hi I am the owner of a 4.0 petrol p38 and she appears to drink a lot of water so head gaskets need sorting. As well as this minor disturbance in the force when going back on the power after overun there is light blue smoke emanating from her exhaust I am assuming piston rings can thsee be changed without taking the engine out of the car?
Always wanted a range rover since the classics first came out and got this one mainly because it is one of the only cars that can curtsy to enable the wife to get in and out as she is disabled, and it is big enough for the great danoodle to stand up in.
Aiming to get the work done next weekend all being well lots of other silly things need looking at so probably not the last time I will be picking your brains
 
depending on how bad the HG has gone, i would be tempted with steal seal if its minor
as for the rings seems like a big job dont know if it could be done with engine in car due to timing set up etc
with them two problems may be easier to source a second hand lump
 
I reckon this needs a bit of investigating. It may be hg it may be a lot of other things. Same with the over run smoke. It could be rings but it could be a blocked breather etc etc. Don't use steel seal wAste of money. What's about miles history oil condition coolant condition.
Btw Piston ring can be changed without removing the engine but I don't advise it life is easier all-round with the engine out trust me!
 
johnnyb70 said:
I reckon this needs a bit of investigating. It may be hg it may be a lot of other things. Same with the over run smoke. It could be rings but it could be a blocked breather etc etc. Don't use steel seal wAste of money. What's about miles history oil condition coolant condition.
Btw Piston ring can be changed without removing the engine but I don't advise it life is easier all-round with the engine out trust me!
Click to expand...
Oil is fairly clean just not a lot of it and water is at present tap water use about 1 litre per 10 miles oops.got gaskets rings big end bearings en route for me to tackle it next weekend.
Also had to buy a new toolkit as tools in my shed disappear faster than biscuits at weight watchers.
 
johnnyb70 said:
I reckon this needs a bit of investigating. It may be hg it may be a lot of other things. Same with the over run smoke. It could be rings but it could be a blocked breather etc etc. Don't use steel seal wAste of money. What's about miles history oil condition coolant condition.
Btw Piston ring can be changed without removing the engine but I don't advise it life is easier all-round with the engine out trust me!
Click to expand...
Don't forget valve stem oil seals,
 
I reckon sensible advice is to strip back to the heads. Check what's going on. Come to a conclusion. By this I mean a true assessment of all the issues. Do not reassemble until your 95%plus certain you've got the measure of what's wrong. Be prepared to remove engine. Putting everything back together if it's no gonna cure the problems is seriously depressing and totally pointless. And will result in this vehicle going for scrap. So commit 2 days to the strip down then be prepared to do the whole job or bail before major spends.
 
You must log in or register to reply here.

Similar threads

A
P38A Broken oil dip stick tube removal
Replies
3
Views
169
AndyF07
A
A
P38A Head Gasket Kit & ARP Bolts ?
2
Replies
23
Views
882
enjoi
enjoi
hef19898
Classic Questions regarding the future
2
Replies
21
Views
1K
norseman
norseman
J
think have bought a 2 tonne paperweight
Replies
10
Views
971
Stanleysteamer
Stanleysteamer
Montyjohn
P38A Adding a valve to manually fill EAS tank and why did my pump fail again?
Replies
14
Views
940
Datatek
Datatek
Back
Top