Freelander 1 Middle exhaust

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
TorsionBhudda

TorsionBhudda

Well-Known Member
Posts
1,342
Location
Falkirk
Hi
My father in law has asked me to do some work to his Feelander 1 for its MOT the center box of the is peeling apart and needs replacing. The whole center section seems to be 1 piece including the CAT. I’m struggling to find the correct replacement part does anyone here have a part number or link to where I can buy the Center section? It’s a 2005 TD4.

Thanks
TB
 
When mine fails. I'm going to fit a universal type stainless steel box, which can be had for as little as £60. These have slip joints, which will slide over the original pipe, once the old box has been cut out.
 
Nodge68 said:
When mine fails. I'm going to fit a universal type stainless steel box, which can be had for as little as £60. These have slip joints, which will slide over the original pipe, once the old box has been cut out.
Click to expand...
That might be an option if I can’t find the proper thing
 
Sounds like the cheap one doesn't contain a working cat in the casing. Not that I'd be worried by that.
 
Am I right in saying that diesels still don't get checked on emissions, so don't need a CAT anyway?
I know my Defender just got checked with a probe for smoke 3 weeks ago and passed first time. - No CAT and no silencer

I remember seeing that the new MOT rules say if a CAT was originally fitted from factory it is a fail if it has been removed, but I'm sure they don't test the emissions, so unless the tester was a bit ar*ey, then it should pass no problem.
 
exmed wayne said:
Am I right in saying that diesels still don't get checked on emissions, so don't need a CAT anyway?
Click to expand...
That's correct. There's no emmision check for a diesel. Just a particulate smoke test.
exmed wayne said:
I remember seeing that the new MOT rules say if a CAT was originally fitted from factory it is a fail if it has been removed, but I'm sure they don't test the emissions
Click to expand...
It just a visual inspection to see if the cat is still fitted. This means the guts can be removed, and as long as it looks ok, it'll pass the MOT.
 
Nodge68 said:
That's correct. There's no emmision check for a diesel. Just a particulate smoke test.

It just a visual inspection to see if the cat is still fitted. This means the guts can be removed, and as long as it looks ok, it'll pass the MOT.
Click to expand...
That's exactly what I thought.
When I put the straight through pipe on my Defender, I was going to weld an empty CAT case over the outside of it, because of all the fuss I'd heard of with the new MOT regs, but I didn't get round to it and it passed anyway, with not a word mentioned. :D
Cheers
 
Nodge68 said:
When mine fails. I'm going to fit a universal type stainless steel box, which can be had for as little as £60. These have slip joints, which will slide over the original pipe, once the old box has been cut out.
Click to expand...

Don't go for a stainless one. It's vicious when in electrical contact with mild steel. You'll get very rapid corrosion of the ends of the old system where the stainless overlaps them (although the stainless box itself will be fine). I'd go for an aluminised mild steel one.
 
From 2001 on Diesels should have a working CAT fitted. I'm going to go with the type approved middle section from ebay as it's still very cheap compared to say buying from kwik fit or paddock etc. Not going down the Stainless route as the back box was replaced just before my father in law bought car and is in great condition.

Another job that needs doing for MOT is replacing the fuel tank cradle as it's almost rotten through. Is this a difficult job any tips? ( may start another thread)
 
exmed wayne said:
Am I right in saying that diesels still don't get checked on emissions, so don't need a CAT anyway?
I know my Defender just got checked with a probe for smoke 3 weeks ago and passed first time. - No CAT and no silencer

I remember seeing that the new MOT rules say if a CAT was originally fitted from factory it is a fail if it has been removed, but I'm sure they don't test the emissions, so unless the tester was a bit ar*ey, then it should pass no problem.
Click to expand...

Think all Diesels from 2001 onwards should have a working CAT. Spoke to one of the suppliers on ebay who said they could supply me the middle section with what looks like a CAT (£65)but would be at my own risk if and no guarantee that would pass MOT. So going for one their type approved middle sections with CAT (£105)
 
Avocet1 said:
Don't go for a stainless one. It's vicious when in electrical contact with mild steel.
Click to expand...
Land Rover use stainless steel for the exhaust pipes, it's low grade stainless, but stainless it is.
The low grade stainless original exhaust and the higher grade replacement box, are close enough in chemical composition to prevent galvanic corrosion from occurring. ;)
Avocet1 said:
You'll get very rapid corrosion of the ends of the old system where the stainless overlaps them (although the stainless box itself will be fine).
Click to expand...
My back box is stainless, mated straight to the corroded stump of the old box. No problem with additional corrosion so far, and it's been on over 3 years now.
 
TorsionBhudda said:
Think all Diesels from 2001 onwards should have a working CAT. Spoke to one of the suppliers on ebay who said they could supply me the middle section with what looks like a CAT (£65)but would be at my own risk if and no guarantee that would pass MOT.
Click to expand...
There's no way the MOT tester can check the cat is working on a diesel. It's a simple smoke particulates test, nothing more. ;)
 
TorsionBhudda said:
Another job that needs doing for MOT is replacing the fuel tank cradle as it's almost rotten through. Is this a difficult job any tips? ( may start another thread)
Click to expand...
There are threads on here describing it - whether you can find them's another matter - Google does a better job of finding threads on here than the inbuilt search.
 
GrumpyGel said:
There are threads on here describing it - whether you can find them's another matter - Google does a better job of finding threads on here than the inbuilt search.
Click to expand...
You're right - and someone cut theirs in half to make it easier to fit, and I think modified it so it bolts back together in situ... Otherwise I suspect it is a subframe-off task.
 
Nodge68 said:
Land Rover use stainless steel for the exhaust pipes, it's low grade stainless, but stainless it is.
The low grade stainless original exhaust and the higher grade replacement box, are close enough in chemical composition to prevent galvanic corrosion from occurring. ;)

My back box is stainless, mated straight to the corroded stump of the old box. No problem with additional corrosion so far, and it's been on over 3 years now.
Click to expand...

Must admit that surprises me? My centre box is going the same way. The outer skin has started to unpeel itself. It certainly LOOKS like aluminised mild steel - it's orange and rusty around where it has failed.
 
You must log in or register to reply here.

Similar threads

S
Exhaust routing
Replies
2
Views
437
sprie
S
Tirran
Replacement exhaust
2
Replies
20
Views
2K
Tirran
Tirran
E
New exhaust for Lightweight
Replies
0
Views
932
elgringo
E
M
D1 EFI manifolds and exhaust into One Ten V8 CSW
Replies
4
Views
449
Mik87
M
V
Used rear differential - will it fit?
Replies
14
Views
1K
victorimba
V
Back
Top