We only get three deliveries a week here, used to be every day
I would just like to say
- Thread starter Hippo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 6,593
- Location
- uk
Dunno, I can't even spell itIs that a euphemism?
brianp38dse
Well-Known Member
- Posts
- 20,065
- Location
- heathrow
Its stupid a decent plasterer and mate would have that all done in a day and cost them less in the long run.Going to get the lying surveyor back and ask him why he told me that it would all be done, ceiling skimmed etc when all they intended to do was go over the last job that was done to put it right.
No communication between surveyors and the people that decide on work to be done, can't understand why it's taken nearly seven months to get to this stage. Couldn't make it up
- Posts
- 33,600
- Location
- North Shropshire
Least i didn't plant it 90 degrees offIt may help in making the error less blatant.
- Posts
- 2,775
- Location
- Seeking shade in the KSA
Problem is that each time they come and do a bit then make an excuse to leave it is a different job, so now I'll have to wait a few weeks while a new job is raised and approved and costed etc before they return to do a bit moreIts stupid a decent plasterer and mate would have that all done in a day and cost them less in the long run.
Then of course the man who arrives wont have permission to do it all so then another job will have to be raised etc etc
- Posts
- 7,877
- Location
- East Midlands
Well, it's the nearest seaside to me when I'm in Wales. I suppose I could go to Aberdovey instead and see how rapacious the wildfowl are there for a change.Nah mate, they're just after yer cheeps!
Wot you doin at Aberwristwatch anyways?
- Posts
- 68,232
- Location
- The Wooly Witch
Stone56
Well-Known Member
- Posts
- 3,216
- Location
- Up a mountain
Stone56
Well-Known Member
- Posts
- 3,216
- Location
- Up a mountain
We only get post if we travel 20klm to the post office to pick it up
WhiskyLassie
Well-Known Member
- Posts
- 5,475
- Location
- Uk
Yess done all my tasks and I can sit and hide 
- Posts
- 16,357
- Location
- Benfleet, Essex
Belated "Morning All" from me.
Running late because..... too much JD consumed last night.
The drive belt(s) I ordered @ 3:30 yesterday have arrived this morning!!! I can get the lathe put back together.
Running late because..... too much JD consumed last night.
The drive belt(s) I ordered @ 3:30 yesterday have arrived this morning!!! I can get the lathe put back together.
- Posts
- 16,357
- Location
- Benfleet, Essex
Lathe is all back together and is "sweet as"..... The missing RPM's have returned now a new smaller and non-slipping belt is on.
Control-box built as per Brian's picture (plagiarism is flattery really....Honest!).
Mine is less profeshernul than wot Brian's is. Mainly because I is dull-witted and I done has fingers like cow's teats.
Also, my drill wandered when cutting the holes out.
I need to determine where to site it, I don't fancy reaching "over" the spinning bits in an emergency.
All mini-lathes have the Emergency stop right on top of the headstock and they put their electronics inside it quite often.
The missing RPM's have returned now a new smaller and non-slipping belt is on.Control-box built as per Brian's picture (plagiarism is flattery really....Honest!).
Mine is less profeshernul than wot Brian's is. Mainly because I is dull-witted and I done has fingers like cow's teats.
Also, my drill wandered when cutting the holes out.
I need to determine where to site it, I don't fancy reaching "over" the spinning bits in an emergency.
All mini-lathes have the Emergency stop right on top of the headstock and they put their electronics inside it quite often.
WhiskyLassie
Well-Known Member
- Posts
- 5,475
- Location
- Uk
That looks fab! Can't wait to see what you makeLathe is all back together and is "sweet as".....
Control-box built as per Brian's picture (plagiarism is flattery really....Honest!).
Mine is less profeshernul than wot Brian's is. Mainly because I is dull-witted and I done has fingers like cow's teats.
Also, my drill wandered when cutting the holes out.
I need to determine where to site it, I don't fancy reaching "over" the spinning bits in an emergency.
All mini-lathes have the Emergency stop right on top of the headstock and they put their electronics inside it quite often.
- Posts
- 12,098
- Location
- Far out West
When I was in school, the lathes had a big red button on the floor you could stamp on to stop them. You could put a big red button on the floor with - ‘Do Not Press’ on it.Lathe is all back together and is "sweet as".....
Control-box built as per Brian's picture (plagiarism is flattery really....Honest!).
Mine is less profeshernul than wot Brian's is. Mainly because I is dull-witted and I done has fingers like cow's teats.
Also, my drill wandered when cutting the holes out.
I need to determine where to site it, I don't fancy reaching "over" the spinning bits in an emergency.
All mini-lathes have the Emergency stop right on top of the headstock and they put their electronics inside it quite often.
- Posts
- 9,098
- Location
- North Lincs
Superb job DanLathe is all back together and is "sweet as".....
Control-box built as per Brian's picture (plagiarism is flattery really....Honest!).
Mine is less profeshernul than wot Brian's is. Mainly because I is dull-witted and I done has fingers like cow's teats.
Also, my drill wandered when cutting the holes out.
I need to determine where to site it, I don't fancy reaching "over" the spinning bits in an emergency.
All mini-lathes have the Emergency stop right on top of the headstock and they put their electronics inside it quite often.
- Posts
- 7,877
- Location
- East Midlands
I see a new structure has gone up near my place in Wales:
That's happened quickly. It wasn't there four weeks ago. It says Vodafone on the gate, but it doesn't seem to be in operation because there wasn't a mobile phone signal in evidence on the iPhone when I was taking the picture. The concrete plinth has bits of plastic conduit sticking out of it with blue plastic rope in them. So maybe it is yet to be wired up. There's a generator running though:
Somebody must have to come and put fuel in it, but there's no sign of fresh wheel marks in the ground. All the mud is looking very smooth from the last heavy rain which is a few days ago now. That gravel area to the right of the generator housing only extends as far as the enclosure round the tower, so to get there one would have to drive over the grass. No wonder mobile telephony is so expensive in this country.
I also spotted an interesting swirly pattern of silt in one of the puddles on a track nearby, that looked like a wiggly worm:
That's happened quickly. It wasn't there four weeks ago. It says Vodafone on the gate, but it doesn't seem to be in operation because there wasn't a mobile phone signal in evidence on the iPhone when I was taking the picture. The concrete plinth has bits of plastic conduit sticking out of it with blue plastic rope in them. So maybe it is yet to be wired up. There's a generator running though:
I also spotted an interesting swirly pattern of silt in one of the puddles on a track nearby, that looked like a wiggly worm:
- Posts
- 22,904
- Location
- In the next Glen
- Posts
- 22,904
- Location
- In the next Glen
- Posts
- 22,904
- Location
- In the next Glen
Evening all, chinky for dinner n a wee beer.
Similar threads
