- Posts
- 44,814
- Location
- East Dorset
So you will be making your slab then?Morning all not sunny today, just waiting on 6 tonnes of ballast & a pallet of cement getting delivered.
Should be all hands on deck on Saturday morning to get mixing.
I would just like to say
- Thread starter Hippo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 22,901
- Location
- In the next Glen
Its for my noo garage
Got 9 tonnes thought 6 might be a bit tight & wont be able to get a deliveryon sat afternoon if ive not got enough.
- Posts
- 22,901
- Location
- In the next Glen
Nope thats just for the outside shuttering, 30cm wide 30cm deep all the way round.
- Posts
- 22,901
- Location
- In the next Glen
I'll get some pics.........
- Posts
- 9,095
- Location
- North Lincs
- Posts
- 7,877
- Location
- East Midlands
Yes, we like pictures of cement being mixed up and concrete being laid.
I did a whole thread about mixing cement on here a few years ago, making a stone faced concrete retaining wall, and putting down some slabs for repairing vehicles on and to provide the bases for sheds and water tanks. It's great fun. It's even more fun if you add in the satisfaction of burying heavy gauge reinforcing mesh.
I did a whole thread about mixing cement on here a few years ago, making a stone faced concrete retaining wall, and putting down some slabs for repairing vehicles on and to provide the bases for sheds and water tanks. It's great fun. It's even more fun if you add in the satisfaction of burying heavy gauge reinforcing mesh.
- Posts
- 22,901
- Location
- In the next Glen
I hope there's a mixer invited to the party
.Are you gonna get that shuttering out after?
J
Drove chassis around field today, needs tick over slowing down so as I can get it in gear and also needs a throttle linkage rather than a piece of string
Hard to steer with no diff but will be better with cab on
Need brakes connecting up as well, might go hydraulic in front
- Posts
- 16,354
- Location
- Benfleet, Essex
Today I struggled with the bearing and bearing stop placements on the inner ends of each side of the rear axle.
No room for any power tools to access inside the outer axle tube to gently open out the bore to allow easy bearing placement.
So it was all by hand
I got both inner bearings installed as a temporary fit in order to see if the removal of the centre section of the axle-tube had allowed the escape of "forces" to drive the two side out of alignment.
Here is a very short video where one of the half-shafts has been inserted all the way through from its own side across the gap and straight into and through the inner bearing on the other side.
No room for any power tools to access inside the outer axle tube to gently open out the bore to allow easy bearing placement.
So it was all by hand
I got both inner bearings installed as a temporary fit in order to see if the removal of the centre section of the axle-tube had allowed the escape of "forces" to drive the two side out of alignment.
Here is a very short video where one of the half-shafts has been inserted all the way through from its own side across the gap and straight into and through the inner bearing on the other side.
- Posts
- 16,354
- Location
- Benfleet, Essex
Looks like a lovely big job.
Do your "Building Control" folks ask for a sample of the concrete (as a "Set" cube) so they can do a strength test of it to see it meets or exceeds the required specification?
- Posts
- 68,228
- Location
- The Wooly Witch
- Posts
- 7,877
- Location
- East Midlands
All looks very diligent and precise. I must admit, I'd have probably just let the shape of the trench define the edges of the concrete for the below ground stuff just for a shed, rather than put boards in. Even so, you'll have a nice neat looking job.
Once that perimeter casting has gone off, will you put a slab over the whole thing to create a floor for the shed?
Stone56
Well-Known Member
- Posts
- 3,213
- Location
- Up a mountain
Not ready mix thenMorning all not sunny today, just waiting on 6 tonnes of ballast & a pallet of cement getting delivered.
Should be all hands on deck on Saturday morning to get mixing.
Last edited:
- Posts
- 9,095
- Location
- North Lincs
Exactly
Stone56
Well-Known Member
- Posts
- 3,213
- Location
- Up a mountain
So you are doing a ring beam with a slab on top the cages look good got a vibro poker makes a he'll of a differences to the strength
- Posts
- 8,999
- Location
- Solent
Hmm, I use quite fruity language when the damn thing ignores me..
- Posts
- 16,354
- Location
- Benfleet, Essex
I did that the other day and Google said "That's Inappropriate".Hmm, I use quite fruity language when the damn thing ignores me..
- Posts
- 22,901
- Location
- In the next Glen
I hope there's a mixer invited to the party
Are you gonna get that shuttering out after?
J
Yer my mate is bringing his tractor n pan mixer
As for the shuttering well we will see
- Posts
- 22,901
- Location
- In the next Glen
Similar threads
