WhiskyLassie
Well-Known Member
- Posts
- 5,552
- Location
- Uk
Morning folks, hope everyone is well.
I would just like to say
- Thread starter Hippo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Stone56
Well-Known Member
- Posts
- 3,392
- Location
- Up a mountain
Thanks for the snippets in the morning hippo it starts my day off on the right foot
Stone56
Well-Known Member
- Posts
- 3,392
- Location
- Up a mountain
Good morning too you have a good day
Hippo
Lord Hippo
- Posts
- 54,168
Later this month we will be cellerbrating 75 years since they first advertised the first prototype Freelander. It were rubbish and nowt like the real fing. But everyone has to start somewhere. Gaydon motor museum will be doing a lr show to cellerbrate on may 7th and 8th. The king will be gerrin a new old crown on the 6th to cellerbrate.
- Posts
- 9,119
- Location
- North Lincs
Morning, absolutely chucking it down today! Staying in bed and having a brew 
Enjoy the day.
Enjoy the day.
WhiskyLassie
Well-Known Member
- Posts
- 5,552
- Location
- Uk
I shall try.
Morning, absolutely chucking it down today! Staying in bed and having a brew
Enjoy the day.
I woke up at half 5 managed to pay in bed 20 mins then decided to get up and watch the rain in my garden
BogdanRtgh
New Member
- Posts
- 1
- Location
- Kyiv
I shall try too
- Posts
- 9,098
- Location
- Solent
Mornin peeps, rainin plenny.
Welcome to the site @BogdanRtgh
Welcome to the site @BogdanRtgh
- Posts
- 16,645
- Location
- Benfleet, Essex
Morning All.
A damp and dreary BH Monday here.
A s ore neck from all that craning & peering at the lathe yesterday.
Have a great day off.
BTW I forgot to bore you all with what I did, so here goes...
Well it was a mixed-bag yesterday, some good bits and some not-so-good bits.
I started to cut the internal circle out of the plate with a standard 6mm tall parting blade and it wasn't too bad; right up until it was sufficiently deep in the metal for the blade to begin jamming and screeching.
This because I was asking a straight tool 6mm tall to operate in a trench that was the curve of the circle that was being cut. Obvious really I suppose.
This necessitated an alternate approach. I removed the plate from the round spigot and swapped the 4-Jaw chucks jaws around for external holding pattern.
But how to centre the work piece with precision? Well, it's not as easy but it can be done and I did get the plate centralised to within about a 'thou.
I then used a hole-saw in the tailstock chuck to remove a decent sized section.
I then did a series of internal "facing" operations to remove all the material you can see from the hole-saw hole to the trench that the parting-off blade had formed.
I then turned the workpiece around, centred it up again and tidied up the inside face.
And here is the finished "giant washer of doom" sitting on top of the SA 8Spd hub flange. It is not as snug/tight a fit on the flange as I would ideally have liked but I was anxious not to encroach on a bevelled/filleted area of the flange. I think it will be OK.
A damp and dreary BH Monday here.
A s ore neck from all that craning & peering at the lathe yesterday.
Have a great day off.
BTW I forgot to bore you all with what I did, so here goes...
Well it was a mixed-bag yesterday, some good bits and some not-so-good bits.
I started to cut the internal circle out of the plate with a standard 6mm tall parting blade and it wasn't too bad; right up until it was sufficiently deep in the metal for the blade to begin jamming and screeching.
This because I was asking a straight tool 6mm tall to operate in a trench that was the curve of the circle that was being cut. Obvious really I suppose.
This necessitated an alternate approach. I removed the plate from the round spigot and swapped the 4-Jaw chucks jaws around for external holding pattern.
But how to centre the work piece with precision? Well, it's not as easy but it can be done and I did get the plate centralised to within about a 'thou.
I then used a hole-saw in the tailstock chuck to remove a decent sized section.
I then did a series of internal "facing" operations to remove all the material you can see from the hole-saw hole to the trench that the parting-off blade had formed.
I then turned the workpiece around, centred it up again and tidied up the inside face.
And here is the finished "giant washer of doom" sitting on top of the SA 8Spd hub flange. It is not as snug/tight a fit on the flange as I would ideally have liked but I was anxious not to encroach on a bevelled/filleted area of the flange. I think it will be OK.
WhiskyLassie
Well-Known Member
- Posts
- 5,552
- Location
- Uk
- Posts
- 23,263
- Location
- In the next Glen
- Posts
- 23,263
- Location
- In the next Glen
WhiskyLassie
Well-Known Member
- Posts
- 5,552
- Location
- Uk
Thinks about the family guy sceneJust w@ting on st@n to qive us @ French lesson on the poop deck.
- Posts
- 23,263
- Location
- In the next Glen
Sun shining here, looking like being a nice day
Nice njoy it tis d@mp n overc@st here @tm good bbq we@ther for us
- Posts
- 23,263
- Location
- In the next Glen
- Posts
- 23,263
- Location
- In the next Glen
- Posts
- 13,794
- Location
- The Principality
"Sunshine and showers for today", they say. Well, so far there has been some 'watery' sun and some showers which are torrential if brief in nature and plenty of cloud in between. We even had a brief spell of lightning. Altogether, the weather here can be described as typical Bank Holiday weather.
Enjoy whatever you are doing today.
Enjoy whatever you are doing today.
WhiskyLassie
Well-Known Member
- Posts
- 5,552
- Location
- Uk
Half 5 is a lay in for me these daysSlept in tod@y I see
WhiskyLassie
Well-Known Member
- Posts
- 5,552
- Location
- Uk
Never w@tched it
Similar threads
