- Posts
- 12,098
- Location
- Far out West
Bought a rattle can to spray my new fool tank.
It's run out of puff and still half full of paint!!
Stick the airline on the nozzle then push it in
I would just like to say
- Thread starter Hippo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Stick the airline on the nozzle then push it in
- Posts
- 22,904
- Location
- In the next Glen
----and cat hanging from the top of the new pole ------
Could be a cataluna flag
- Posts
- 22,904
- Location
- In the next Glen
- Posts
- 22,904
- Location
- In the next Glen
Can someone pick this up & do landyzone courier lol..........
snap on tool box with tools INCLUDED | eBay
snap on tool box with tools INCLUDED | eBay
Hippo
Lord Hippo
- Posts
- 53,847
Need ter film yerself doing it anorl.Stick the airline on the nozzle then push it in
- Posts
- 12,098
- Location
- Far out West
- Posts
- 44,834
- Location
- East Dorset
Sure the jet ain't just blocked?Bought a rattle can to spray my new fool tank.
It's run out of puff and still half full of paint!!
- Posts
- 33,600
- Location
- North Shropshire
Putting air in and it will start to cure in next to no time and clog up
- Posts
- 33,600
- Location
- North Shropshire
- Posts
- 12,098
- Location
- Far out West
Putting air in and it will start to cure in next to no time and clog up
Have you tried squeezing the can a bit? Usually gets a bit more out
- Posts
- 44,834
- Location
- East Dorset
Fill it to below full with polyfilla then finish it off with that special finishing filler. You might even be able to sort of paint it on wiv a brush. And be prepared for a feck load of sanding back, refilling etc.
I had to cut a foot square of plasterboard out when moving a rad not long ago, in our noo kitchen. There wasn't much to attach the new bit of plasterboard to. Even with a special wide plasterer's filling trowel thing it took ages and I know it still isn't quite right though no one else seems to be able to see it! At least it is only at about calf height, in a corner.
Anyway, if you can plaster with the new box in place, obvs not the socket, maybe one of them would help.
Like this one.
https://www.screwfix.com/p/magnusso...VhO7tCh1WFwkoEAQYASABEgK6fvD_BwE&gclsrc=aw.ds
Best of luck, Typical of a job that you think will take 20 mins tops and your'e still at it three days later, what with waiting for things to go off. AND you are leaning over the work top to do it and getting back ache.
- Posts
- 44,834
- Location
- East Dorset
So that's at least three hands needed then.
and cleaner to clean t he paint off his phone!!
- Posts
- 44,834
- Location
- East Dorset
He could put it in a bucket of hot watter, might increase the pressure of whatever the propellant is, if there is any left at all.
- Posts
- 33,600
- Location
- North Shropshire
I see some nobs have just thrown paint at an Aston Martin dealership. They didn't choose a vauxhall dealer. Are they just sore because they don't have jobs and can't afford nice cars?
doriz
Well-Known Member
- Posts
- 17,312
Pointless act, pointless
- Posts
- 33,600
- Location
- North Shropshire
My ctek charger comes with its own connectors.. think i might chop them off and put something better on!!
Make it easier to move the charger around, plus it gets warm so it's obviously rubbish
Make it easier to move the charger around, plus it gets warm so it's obviously rubbish
- Posts
- 16,358
- Location
- Benfleet, Essex
I use their little Traffic-light tell-tale that connects to the battery that has their quick-connector so I can plug the charger onto either car.
On the Rangie I can fish the tell-tale out from between the bars of the radiator shroud to check the battery state and then connect there. I don't even have to open the bonnet.
doriz
Well-Known Member
- Posts
- 17,312
Let’s hope they don’t take aim at David Brown anorl
- Posts
- 44,834
- Location
- East Dorset
Fink they'd have to do to the graveyard to do that!!!Let’s hope they don’t take aim at David Brown anorl
- Posts
- 33,600
- Location
- North Shropshire
Who?Let’s hope they don’t take aim at David Brown anorl
Similar threads
