- Posts
- 13,787
- Location
- The Principality
Your scenery couldn't be more opposite to mine if it tried!
But the dog's enjoying it just the same.
I would just like to say
- Thread starter Hippo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
But the dog's enjoying it just the same.
- Posts
- 9,095
- Location
- North Lincs
4 hours later the garden is now clear! Next step is to fix the fence then we can leave it until grass cutting season starts
- Posts
- 13,787
- Location
- The Principality
Now go and have a well deserved cuppa.4 hours later the garden is now clear! Next step is to fix the fence then we can leave it until grass cutting season starts
Do we get before and after piccies?
- Posts
- 9,095
- Location
- North Lincs
No pictures, I am too embarrassed by the pile I allowed to build up!! Put it this way, he drives a 3.5ton truck and we filled itNow go and have a well deserved cuppa.
Do we get before and after piccies?
Hippo
Lord Hippo
- Posts
- 53,837
Hava search ont youtube for fixes others have done to theirs.Mid-morning All
Another late rising here
This has to stop, just because I am now an official pensioner is no real excuse for tardiness.
No snow here.
My new lathe is kaputski and in pieces on the work bench. The drive system is in need of some re-design as it chews belts and spits them out again. The toothed pulleys aren't properly aligned, the belt just destroys itself trying to break free and climb the side wall of the drive pulley and they have made it so tight that it strips the teeth away and puts undue stress on the main spindle bearings. Not good at all in this respect.
I will see what I can do to resolve it with some proper alignment, a new (longer) belt and some form of tensioner.
Have a great day everyone.
doriz
Well-Known Member
- Posts
- 17,312
Well mi rafters is constructed and mi sawdust pile just needs cleaning up.
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
I finally remembered to sharpen me penknives.
- Posts
- 16,352
- Location
- Benfleet, Essex
Yup, been there and done that for all the "common problems" with these styles of lathes.
Sadly, my problem isn't up there except for one poor sausage whose MX 8 x 14 is in a far worse state than mine
I can probably fix it, but I shouldn't have to. It has run for <2-hours and it is stripping the belt of teeth and just isn't "right".
I am in touch with the supplier and we are "doing the dance" where he pretends he is trying to help me and I pretend I believe him.
These are essentially simple machines but the way they have organised the main drive on this one is pretty awful.
I have asked them to provide a new drive belt (for a start) and they have suggested I alter the motor's position to lessen the strain on the belt.
Trouble is, the motor pulley has been hammered onto the motor-spindle and is immovable along the shaft and the motor mount points are bolt holes and not "slots" so the degree of movement is extremely limited.
I will get there and I will fix it. It is just ruddy annoying.
- Posts
- 9,095
- Location
- North Lincs
You know, when I started to look for a new lathe, I did think of getting a Chinese one. So many people have videos of them having problems I went with a 1949 Smart & Brown. I still have problems that require sorting but I think, hey its older than me!!Yup, been there and done that for all the "common problems" with these styles of lathes.
Sadly, my problem isn't up there except for one poor sausage whose MX 8 x 14 is in a far worse state than mine
I can probably fix it, but I shouldn't have to. It has run for <2-hours and it is stripping the belt of teeth and just isn't "right".
I am in touch with the supplier and we are "doing the dance" where he pretends he is trying to help me and I pretend I believe him.
These are essentially simple machines but the way they have organised the main drive on this one is pretty awful.
I have asked them to provide a new drive belt (for a start) and they have suggested I alter the motor's position to lessen the strain on the belt.
Trouble is, the motor pulley has been hammered onto the motor-spindle and is immovable along the shaft and the motor mount points are bolt holes and not "slots" so the degree of movement is extremely limited.
I will get there and I will fix it. It is just ruddy annoying.
It doesn't really matter which way you go, if it is a bad one, it will give trouble sadly
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
Is it a steam powered one?
- Posts
- 9,095
- Location
- North Lincs
No, it does have flat belts but it was an early uptake of the electric motorIs it a steam powered one?
- Posts
- 16,352
- Location
- Benfleet, Essex
Yes, a lot of "Home Lathes" were "treadle-powered" before small electric motors came along.No, it does have flat belts but it was an early uptake of the electric motor
I did think of getting a Myford ML7 (or similar) but they are commanding £1 .. 1.5K prices it seems.
I could just write this off as a salutary lesson and go elsewhere, but I will do my best to resolve it first.
I might just be lucky enough that this is the only real problem with the machine.
I think MOST machines are now "Made In China" and the truth of it is that all things are made to a specification and a price-point detailed in a contract somewhere.
Some of the German branded lathes are actually Made In China, but the specification and QC is properly applied.
- Posts
- 83,276
- Location
- Embasinga stocæ
I like my Chinese mini lathe (Warco WM180). its a quite reasonable bit of kit.
- Posts
- 9,095
- Location
- North Lincs
I did too as that was what I had sold 7 years ago (foolishly!!) I actually paid £700 for my S&B but it came with a new 3ph motor and VFD (Siemens) and also a shed load of tooling, chucks and spares.
I later acquired another Model M lathe for nothing so I am good for spares
I hope you can fix it and maybe even improve it!
- Posts
- 16,352
- Location
- Benfleet, Essex
Yes, the Warco WM-180 is pretty decent by all accounts, but was a bit more than I was contemplating spending. Now I wish I had bitten the bullet and spent a bit more. LOL.I like my Chinese mini lathe (Warco WM180). its a quite reasonable bit of kit.
Live & Learn I guess.
- Posts
- 83,276
- Location
- Embasinga stocæ
One of the reasons I went for a new one, was that a lot of the older lathes are knackered and I didnt want to spend hundreds get one back in to spec.I did too as that was what I had sold 7 years ago (foolishly!!) I actually paid £700 for my S&B but it came with a new 3ph motor and VFD (Siemens) and also a shed load of tooling, chucks and spares.
I later acquired another Model M lathe for nothing so I am good for spares
I hope you can fix it and maybe even improve it!
- Posts
- 83,276
- Location
- Embasinga stocæ
mine was about £1000 including 2 axis DRO.
- Posts
- 9,095
- Location
- North Lincs
Whilst I do agree and nearly did the same, I doubt your Warco will still be churning out parts in 70 years time like my old S&B
I don't have anything against them I just like a lathe that knows how I feel (knackered) lol
- Posts
- 16,352
- Location
- Benfleet, Essex
If that was inc. VAT that's a very keen deal indeed.
This little P.O.S. was £599 with all the usual "
I will persevere.
- Posts
- 83,276
- Location
- Embasinga stocæ
I am not sure how many 140 year olds are operating lathes?Whilst I do agree and nearly did the same, I doubt your Warco will still be churning out parts in 70 years time like my old S&B
Do you have any imperical date to support your hypothesis?
Similar threads
