Hertfordshire Lanes?????

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Of course you are welcome! I will be working at my dads house tomorrow and over the weekend on the Luton/Dunstable boarder as I need to use the press, I have a customers bushes to replace on his disco While I sort mine out Jai
 
jai_landrover said:
Of course you are welcome! I will be working at my dads house tomorrow and over the weekend on the Luton/Dunstable boarder as I need to use the press, I have a customers bushes to replace on his disco While I sort mine out Jai
Click to expand...


Jai pm me the address and i'll probably come and join you, always willing to lend a hand n will do me good to pick up some experiance of taking the buggers appart!

Cheers

Dan
 
Oil pump reassembled and attached.

Oil Filter in place.

New oil in sump.

NO OIL PRESSURE!!!!!!!!!!!!!

Looks like I'm taking the sump off tomorrow night to check the pick up pipe. And before anybody says it, yes I did prime the pump. Looks like a case of Range Rover Revenge - anybody got a cure lol!!
 
jai_landrover said:
Of course you are welcome! I will be working at my dads house tomorrow and over the weekend on the Luton/Dunstable boarder as I need to use the press, I have a customers bushes to replace on his disco While I sort mine out Jai
Click to expand...
My mate and i done my bushes on friday night 4hrs to do them all plus some welding on my exhust and some greasing up good luck mate make sure you have a big hammer and teh easy way we found to get some back into place was to drop it dowm slowly and bending out the brackets a lil touch. And Kev 5lt of unleaded and a match :D just messing know how ya feel tho
 
RangeyV8 said:
My mate and i done my bushes on friday night 4hrs to do them all plus some welding on my exhust and some greasing up good luck mate make sure you have a big hammer and teh easy way we found to get some back into place was to drop it dowm slowly and bending out the brackets a lil touch.
Click to expand...


Rangie,

They should be ok got a 20 tonne press makes light work of the stubbornest bushes! well I'm hoping to change my alternator tomorrow fit new brake lines to my axle and remove the old rear axle and possibly refit new one. Been seriously thinking about an onboard pc to run mapping, gps software and sound system. I'll do some more thinking and let you know what I decide. memory map would be great with a decent touch screen. Jai
 
jai_landrover said:
Just out of interest Kev how did you prime the pump? Vasolene or lecky drill through the dizzy? Jai
Click to expand...

Did the leccy drill manouvre after turning engine on starter with king lead removed.

After that tried injecting oil with big oil syringe through return pipe from oil cooler (coz it was easy to get at) and also through pressure switch mount. Also, left oil cooler pipe disconnected and turned the engine over and also did the drill trick again. Not a drop of oil was seen.

Removed pressure switch did it all again, only a dribble!! No sticking or grinding noises on pump drive so as far as I can tell the pump is working its' just not picking up oil. What ya thinkin??
 
I would have said if you used vasolene, to go for the drill method but you already have, its always worked in the past. I know people say that if the old gears have been removed and refitted to be in the exact same way as they wear together if the idler gear was put in upside down they would not mesh as well or pump as well. But I know you have probably put them back as was. Sorry Don't know. :-( Jai
 
jai_landrover said:
I would have said if you used vasolene, to go for the drill method but you already have, its always worked in the past. I know people say that if the old gears have been removed and refitted to be in the exact same way as they wear together if the idler gear was put in upside down they would not mesh as well or pump as well. But I know you have probably put them back as was. Sorry Don't know. :-( Jai
Click to expand...

Thanks mate, I don't know either:mad:

The drill method has always worked for me in the past, the cordless slows down and gets hot as soon as the pump is doing its' thing so I know when it has primed. this time no joy.

What I might do is drop the sump, remove pick up and strainer, give 'em a clean then with the oil syringe pump oil into the pickup pipe and take it from there. Will get it sorted eventually. Can't wait to get back out on the lanes.

Cheers.
 
Rangie, Remember if the cage is to be certified it has to pass MSA requirements to be classed as a legal cage for comps. Even Jamies one is now technically no good as somone has drilled into the frame to mount lights. It shouldn't pass an MSA inspection. Welding should be up to scratch there are so many cages that shouldn't be used. check out the MSA Blue Book for requirements. Jai
 
Update on Tonka. DB fitted Crank and Pistons tonight. I attacked passenger bucket seat subframe. Tomorrow test fit of engine, I recon Battery Box will have to come off and relocate to under passenger seat, which is no loss really, as bucket seat has put paid to me using the seat locker, so I might as well stick the battery in it.
O/S engine mount will need refabricating for sure as Injector Pump fouls.
I can lose the Series Vacuum Tank, as the new engine doesn't need it. Gives a bit more room for the raised air intake pipework.
Really good to see things going back together.:D Loads still to do though.:eek:

Kev sorry you've still got engine woes.
 
You must log in or register to reply here.

Similar threads

A
Peak District lanes
Replies
8
Views
1K
Anaconda
A
A
Non Scratchy Greenlane Trip Berkshire/Wiltshire
Replies
10
Views
2K
Anaconda
A
T
Any Series Owners in the Phoenix Area?
Replies
9
Views
585
Bobsticle
Bobsticle
A
Greenlane trip 19th August
Replies
7
Views
2K
Anaconda
A
Shogun243
LLandrillo - Wayfarer
Replies
1
Views
915
300bhp/ton
300bhp/ton
Back
Top