Hertfordshire Lanes?????

Leebastard · Jun 15, 2014

Farrar said:
how you doing lee. Are you busy working. long time.

I'm alright mate ta. Been working like a dog as usual. Off on tour again on Wednesday until the en of July. How are you mate?

Farrar · Jun 15, 2014

Leebastard said:
I'm alright mate ta. Been working like a dog as usual. Off on tour again on Wednesday until the en of July. How are you mate?

im all good thanks. busy working. not enough play time

danp3 · Jun 16, 2014

stutab said:
I have a bender which you are welcome to use.

ah nice. I assume it can do 75mm stainless tube to about 30'?

stutab · Jun 18, 2014

Ye goes that big, only problem is if it's thin walled it will probably crease it.

danp3 · Jun 18, 2014

Haha. Ive just been to the scrap yard and could only find really heavy stuff, I'd guess 2-3mm wall. So I left it, thinking it would be to hard to bend.

jai_landrover · Jun 18, 2014

danp3 said:
Haha. Ive just been to the scrap yard and could only find really heavy stuff, I'd guess 2-3mm wall. So I left it, thinking it would be to hard to bend.

2 or 3mm wall will bend perfect in Stus bender

Anything thin will wrinkle or kink can get slightly better results by compacting sand in the tube and bending it. However sand and intake don't mix!

thicker wall will bend better tho.

Go get some tube from the scrappy!!!

danp3 · Jun 18, 2014

Might be going back there then. Spent ages there today rummaging through a skip full of aircraft parts. Very cool

jai_landrover · Jun 18, 2014

Dan would you mind pm ing me the scrappy I need some ford bits unfortunately and need a decent scrappy

danp3 · Jun 18, 2014

It's not a car scrap yard, sorry. Just general metal. They hold a lot of stock steel and tons of assorted metals that they have hoarded over the years. I can't go there without spending hours rummaging

KillaJoules · Jun 19, 2014

danp3 said:
It's not a car scrap yard, sorry. Just general metal. They hold a lot of stock steel and tons of assorted metals that they have hoarded over the years. I can't go there without spending hours rummaging

Ahhh, scrappy porn :smokin:

There used ro be (probably still is) a good scrappy like that in Hunslet, Leeds, where me and my brother used to go hunting for stuff, So long as you kept out of the way of the plant machinery they let you wander around looking for owt you wanted.

danp3 · Jun 19, 2014

Sounds similar. Got some alu sheet for new footwell, alu box section to reinforce it, a bit of ss tube and a cool looking bit of titanium off an airplane for a tenner. Can't get that down Tesco

stutab · Jun 19, 2014

Where is this magnificent place?

danp3 · Jun 19, 2014

Biggleswade down the a1 just north of baldock services

KillaJoules · Jun 19, 2014

Where my Defender box was replaced

danp3 · Jun 19, 2014

Are there any disco 300tdi specialists out there know what this bit does?

there wasnt one on the 200

jamesmartin · Jun 19, 2014

yes goes into a y piece with a pipe from rad to a connector under header tank

danp3 · Jun 19, 2014

Hmm that could be a problem. Sounds like I needs me one of them hoses

discostew38 · Jun 19, 2014

danp3 said:
Biggleswade down the a1 just north of baldock services

I live round there and I've not seen one ??
Could be handy

sm0129 · Jun 19, 2014

I go to this one-

Skip hire, steel stockholding, waste and metal recycling at F.D.O'Dell & Sons Ltd

danp3 · Jun 19, 2014

That's the one

Hertfordshire Lanes?????

Active Member

Well-Known Member

New Member

Well-Known Member

New Member

Well-Known Member

New Member

Well-Known Member

New Member

Active Member

New Member

Well-Known Member

New Member

Active Member

New Member

Well-Known Member

New Member

Active Member

Active Member

New Member

Similar threads