tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Looks the same colour as yours mate, paint code 601? You dropping a hint 
P38A Electrickery drain,where am I going wrong?
- Thread starter tomcat59alan
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
It's 1998my, if the rain goes off I'll check again ,think I heard the sounder chirp when I pulled /reinserted the fuse so you may be on to something there. No nanocom, is there anything I can disconnect to eliminate it out of the list of possibilities?
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Looks the same colour as yours mate, paint code 601? You dropping a hint
Now there's a thought!
Would have to check but mine's rioja red, I think.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Have to wait till this evening when I can dig out RAVE. I'd just disconnect the sounder. I did on my Omega with no issues other than it blared for about 30 minutes until the battery went flat.
brianp38dse
Well-Known Member
- Posts
- 20,065
- Location
- heathrow
Paint code 601 is rioja red it is a very nice colour, hum car as spares now there's an idea I could do with a driver front wing in that colour
I could do with a driver front wing in that colourtomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Paint code 601 is rioja red it is a very nice colour, hum car as spares now there's an idea
Pair of cheeky buggers,
- Posts
- 16,357
- Location
- Benfleet, Essex
Mines Rioja red too, and no its not available for spares.
The BBUS is located on the top of the inner wing under the battery tray area and has a pull out connector, so that's a good and simple thing to pull apart.
Mine was disconnected when I got the car, so I reconnected it. Are the internal batteries inside it replaceable I wonder?
The BBUS is located on the top of the inner wing under the battery tray area and has a pull out connector, so that's a good and simple thing to pull apart.
Mine was disconnected when I got the car, so I reconnected it. Are the internal batteries inside it replaceable I wonder?
- Posts
- 16,357
- Location
- Benfleet, Essex
Just seen a post that suggests that the "ageing" batteries in the BBUS (if fitted) can place a continuous "re-charge" load/drain onto the main battery.
So it is well-worth pulling the BBUS connector as a test. If you have the bonnet lock-switch fooled and can wait till the BeCM goes to sleep and the 0.164 amps is seen, pop the BBUS connector and see what happens to your amps reading?
I would be interested to hear what you get @tomcat59alan
So it is well-worth pulling the BBUS connector as a test. If you have the bonnet lock-switch fooled and can wait till the BeCM goes to sleep and the 0.164 amps is seen, pop the BBUS connector and see what happens to your amps reading?
I would be interested to hear what you get @tomcat59alan
- Posts
- 16,357
- Location
- Benfleet, Essex
Ahhhhh....
Just read this in the Electrical troubleshooting manual......
Two different types of Alarm Sounders are available:
1. Normal Alarm Klaxon (Alarm Sounder (Z171))
2. Battery Backed Up Alarm Sounder (Z272) The Battery Backed Up Alarm Sounder (Z272) is an alarm sounder which contains its own internal battery.
When the ignition is on, the internal battery is charged via an ignition feed. If either the connector is removed or the wires to it are cut, then the sounder will sound for 4.5 minutes.
(So, this means it can only draw current for charging while the ignition is switched on).
To disconnect the Battery Backed Up Alarm Sounder (Z272):
Turn Ignition On (Pos. II).
Turn Ignition Off.
Disconnect within 17 seconds.
To silence if triggered:
Connect.
Disarm Alarm.
Turn Ignition On (Pos. II).
Just read this in the Electrical troubleshooting manual......
Two different types of Alarm Sounders are available:
1. Normal Alarm Klaxon (Alarm Sounder (Z171))
2. Battery Backed Up Alarm Sounder (Z272) The Battery Backed Up Alarm Sounder (Z272) is an alarm sounder which contains its own internal battery.
When the ignition is on, the internal battery is charged via an ignition feed. If either the connector is removed or the wires to it are cut, then the sounder will sound for 4.5 minutes.
(So, this means it can only draw current for charging while the ignition is switched on).
To disconnect the Battery Backed Up Alarm Sounder (Z272):
Turn Ignition On (Pos. II).
Turn Ignition Off.
Disconnect within 17 seconds.
To silence if triggered:
Connect.
Disarm Alarm.
Turn Ignition On (Pos. II).
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Paint code 601 is rioja red it is a very nice colour, hum car as spares now there's an idea
Yeah, my driver's door has a couple of splodges of electrolytic oxidation. My seats are getting a bit tired too. Always nice to have a spare engine. Any idea where there might be lawn ornament someone would want to get shot of?!
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
I disconnected the sounder and it never made any difference until I plugged it back in and the discharge increased meant to note the readings but my mate turned up with a sick Smart car, what a heap of sh1t.Just seen a post that suggests that the "ageing" batteries in the BBUS (if fitted) can place a continuous "re-charge" load/drain onto the main battery.
So it is well-worth pulling the BBUS connector as a test. If you have the bonnet lock-switch fooled and can wait till the BeCM goes to sleep and the 0.164 amps is seen, pop the BBUS connector and see what happens to your amps reading?
I would be interested to hear what you get @tomcat59alan
brianp38dse
Well-Known Member
- Posts
- 20,065
- Location
- heathrow
Dan stop helping him we want some spares
- Posts
- 16,357
- Location
- Benfleet, Essex
As soon as there looks to be a fine day again I will have a dabble looking for the current draw on mine too.
Luckily, I have a CTEK "Comfort" connector so the charger can ensure the BeCM doesn't lose power while I put an ammeter in the earth line.
Then, If I can see how to fool the bonnet-closed switch off we go measuring the current-draw.
Will update with whatever I find too.
Luckily, I have a CTEK "Comfort" connector so the charger can ensure the BeCM doesn't lose power while I put an ammeter in the earth line.
Then, If I can see how to fool the bonnet-closed switch off we go measuring the current-draw.
Will update with whatever I find too.
- Posts
- 16,357
- Location
- Benfleet, Essex
PMSL. Ahhhh.... I see. You think this is a likely outcome then?Dan stop helping him we want some spares
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Not a hope in hell.
brianp38dse
Well-Known Member
- Posts
- 20,065
- Location
- heathrow
Everything is fixable, its just finding what to fix is the pain in the backside.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
- Posts
- 16,357
- Location
- Benfleet, Essex
Eek! Will try to simulate an inserted bonnet latch and not destroy anything.
They are steel bolts in plastic and 3 of the 4 came out fairly easily, the last one sheared off like it was made from cheese.
It would be fairly easy to put a nut and bolt through instead, I just didn't have enough time when I replaced the bonnet cables.
It would be fairly easy to put a nut and bolt through instead, I just didn't have enough time when I replaced the bonnet cables.
Similar threads
