- Posts
- 83,282
- Location
- Embasinga stocæ
Diesel Do's L Series
- Thread starter Dieseldo01
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
DastardlyDan
Active Member
- Posts
- 287
across wires 6 and 7 on the pump
Diesel Do
Well-Known Member
- Posts
- 5,213
- Location
- Nottingham
Alibro
Well-Known Member
- Posts
- 7,182
- Location
- Northern Ireland
Crackin!
Are they still the same height and driving position as the LR ones?
Are they still the same height and driving position as the LR ones?
Diesel Do
Well-Known Member
- Posts
- 5,213
- Location
- Nottingham
Got them lower and a bit further back. The drivers one goes up and down like magic!
Alibro
Well-Known Member
- Posts
- 7,182
- Location
- Northern Ireland
So where are the photos and the how to?
Comon bud your slacking!
Comon bud your slacking!
Diesel Do
Well-Known Member
- Posts
- 5,213
- Location
- Nottingham
Had to make complete new subframes and modify the Subaru bases as they bolt straight to the floor.
Diesel Do
Well-Known Member
- Posts
- 5,213
- Location
- Nottingham
Not seen much of you in here recently DD. Nice work on the Freelander. I look forward to seeing it done.
GrumpyGel
Well-Known Member
- Posts
- 26,393
- Location
- Christchurch, New Zealand
I have a hankering to fit those 1/2 leather seats with the Land Rover printed material out of a County Disco.
+1
Alibro
Well-Known Member
- Posts
- 7,182
- Location
- Northern Ireland
Nice work, keep the updates coming, some of us have so little going on in our lives we like to watch what your doing.
davidsmith1307
Well-Known Member
- Posts
- 1,333
- Location
- Hull
Nice work, keep the updates coming, some of us have so little going on in our lives we like to watch what your doing.
....clicks "Watch Thread"
Diesel Do
Well-Known Member
- Posts
- 5,213
- Location
- Nottingham
Got a lot to do still. Picking up a spare box to rebuild cos the one in its knackered. Got a spare rebuilt ird going to swap them over when the box is ready. Need you source an uprated clutch ????
I was going to change the final drive to suit my wheel size. But going to work on the principle that the extra torque from tuning it should cope! Maybe? It's much more grunty than my 1.8 so hope it'll be a lot less noticeable. Then the prop off my green one can go on. It's 2wd and going on the noises I can only think ird about to jump out of the bonnet
Handbrake has been causing a lot of head scratching but I think I've sussed it now just need to source some cables. The suspension arms get in the way and the cable would be too low, so probably get ripped off off-road
I was going to change the final drive to suit my wheel size. But going to work on the principle that the extra torque from tuning it should cope! Maybe? It's much more grunty than my 1.8 so hope it'll be a lot less noticeable. Then the prop off my green one can go on. It's 2wd and going on the noises I can only think ird about to jump out of the bonnet
Handbrake has been causing a lot of head scratching but I think I've sussed it now just need to source some cables. The suspension arms get in the way and the cable would be too low, so probably get ripped off off-road
Alibro
Well-Known Member
- Posts
- 7,182
- Location
- Northern Ireland
Sounds like you have your hands full. Thankfully I caught my VCU's before they did any serious harm.
Gerty is ready for MOT now so fingers crossed, she goes on Sat 30th.
Gerty is ready for MOT now so fingers crossed, she goes on Sat 30th.
Diesel Do
Well-Known Member
- Posts
- 5,213
- Location
- Nottingham
I'm looking to get some longer shafts made.
Looks like I've finally sussed the handbrake too
Diesel Do
Well-Known Member
- Posts
- 5,213
- Location
- Nottingham
Alibro
Well-Known Member
- Posts
- 7,182
- Location
- Northern Ireland
Nice, you going to flair the arches more or leave as is?
GrumpyGel
Well-Known Member
- Posts
- 26,393
- Location
- Christchurch, New Zealand
Would you get a MOT with the wheels poking out that far? I don't think you'd get a WOF over here like it.
Diesel Do
Well-Known Member
- Posts
- 5,213
- Location
- Nottingham
It's a bit boarder line but I think so. Plan is to fit the body kit arches. But remove the stripey bits. They should cover them.
Diesel Do
Well-Known Member
- Posts
- 5,213
- Location
- Nottingham
Did I mention I'm working on a high steer kit to eliminate the bodywork catching issue on full droop?
