Defender 90 300tdi strip down and rebuild

bustersbus · Jul 16, 2011

Allyipod said:
P.S. A word of Warning. Never Never!! use a grinder with the garde plate removed. The wheel broke up and went through gloves and cut my middle finger left hand to the bone. Pic to follow. Ouch :doh:

Allyipod said:
Not the best of photos but it gives you the idea.

Guid yin!

Ah did summit the same, but mines went up and down the finger!

fleck · Jul 16, 2011

would make for an interesting call to parcelforce though

Allyipod · Jul 16, 2011

sible88 said:
What a rot box!! Is that a genuin 300?

You got it in one yes it is gen but rotten. As i said with the parts iv'e bought i could build a new one lol.

Allyipod · Jul 16, 2011

bustersbus said:
Guid yin! Ah did summit the same, but mines went up and down the finger!

Hi Buster
Aye it was a sore one. Wrapped a bit of bog roll round it and i was good to go. lol

bustersbus · Jul 16, 2011

Allyipod said:
Hi Buster
Aye it was a sore one. Wrapped a bit of bog roll round it and i was good to go. lol

Aye

Ah used some Blue roll and insultin' tape on mine.. ye can hardly see the scar now

There's a lot tae be said fur they thin discs

Allyipod · Jul 16, 2011

fleck said:
would make for an interesting call to parcelforce though

One of my mates works for DHL and he is up and down the country like a W ores Well you get the jist so getting a part from the south is not a problem.

jamesmartin · Jul 16, 2011

thats a proper mechanics plaster blue roll and insulation tape,soaks up alot of blood

sible88 · Jul 16, 2011

That would of done me over!!
I faint at the sight of blood!!!

Allyipod · Jul 16, 2011

P.S Has anyone got a good tub as i am still looking. Picked up a good seat base from a guy on E-bay arrived today and i had to modify it but still a good buy...

jamesmartin · Jul 17, 2011

i might have but poor cappings ill check monday

Allyipod · Jul 17, 2011

sible88 said:
That would of done me over!!
I faint at the sight of blood!!!

You sould not buy a landy. lol

sible88 · Jul 17, 2011

Too late owned one for a year it's had 4 engines and passed out twice since ownership

Allyipod · Jul 17, 2011

sible88 said:
Too late owned one for a year it's had 4 engines and passed out twice since ownership

Just up out my bed and it is ****ing down rain. Hope it clears up later on as i want to get the bulkhead off. The engine and box seem to be the only good parts on my fender according to the speedo it has done 176k although the engine No does not match the log book No. So it has had a change at some time in the past.

Allyipod · Jul 17, 2011

Here are some more pics from today. Got the bulkhead off and am going to speak to the local farmer to see if he will come up with his telehandler and lift out the engine and gearbox.

Better get it done soon before the weeds take over

Allyipod · Jul 17, 2011

The handbreak shoes were covered in thick oil. Is it an easy job to change the seal on the back of the transfer box.

jamesmartin · Jul 17, 2011

yes just remove flange 30mm socket lever out old seal and replace grease rear of seal to hold garter swpring in while tapping home seal,you will feel when its in far enough ,after fitting flange put some silicone sealant around shaft and flange before fitting washer and nut

The Mad Hat Man · Jul 17, 2011

yes
you just need a pretty large socket or similar to tap the new one in.

Allyipod · Jul 17, 2011

Has anyone got a part No for this seal. I have looked at the pdf file but cannot see it in the list.

jamesmartin · Jul 17, 2011

ftc7043 is one for flange with no mudshield ftc4939 if has but can be used for both

Allyipod · Jul 17, 2011

jamesmartin said:
ftc7043 is one for flange with no mudshield ftc4939 if has but can be used for both

Sorry James just been out to look, how do you know if it has a mudshield?

Defender 90 300tdi strip down and rebuild

Well-Known Member

Well-Known Member

Active Member

Active Member

Well-Known Member

Active Member

Well-Known Member

New Member

Active Member

Well-Known Member

Active Member

New Member

Active Member

Active Member

Active Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Active Member

Similar threads