Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Haha send me a pm when you're ready then 
Bumper build
- Thread starter Dr_evil
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Ere Drivel Some cheap steel for ya Check out his other items as well
http://www.ebay.co.uk/itm/Flat-Bar-..._Metalworking_Supplies_ET&hash=item19d59b8f6b
http://www.ebay.co.uk/itm/Flat-Bar-..._Metalworking_Supplies_ET&hash=item19d59b8f6b
chunkymunky
New Member
- Posts
- 9,901
- Location
- worcestershire
Going to replace all my cobbled silicon tubing and couplings with a bespoke pipe from airbox to turbo. Reckon I need a decent stainless pipe supplier. Think it's 63mm I need or 58mm I forget now.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Have a look at exhaust suppliers they are usually cheapest
chunkymunky
New Member
- Posts
- 9,901
- Location
- worcestershire
Hmm ok cheers
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Bumper and one slider fully capped, only had an hour free today by hoping to get the last one done tomorrow and then folders the welds. Was thinking 10 hours to do everything on about 7 so far so doing well
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
The welds look a bit bulkier in the pics than they actually are, going to give them a quick once over with the flap disk tomorrow
chunkymunky
New Member
- Posts
- 9,901
- Location
- worcestershire
Me mig would be jealous!
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
chunkymunky
New Member
- Posts
- 9,901
- Location
- worcestershire
haha what him and his hobby mig that cant do 1.2mm disco floors
Reckon I could better than him after a few hours practising
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
haha what him and his hobby mig that cant do 1.2mm disco floors
oi doc,when you goona start on my rock/tree sliders for my disco then
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
most probably! you work with wood so steady hand should help, that was about 8mm in total I was welding through so had to turn the amps right up haha
5.5mm box and the plate was about 5mm too so where it overlapped probably about 8
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
oi doc,when you goona start on my rock/tree sliders for my disco then
Don't remember you making an order
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
Don't remember you making an order
ya bugger,i asked you when i first bought the disco,mind you i think you had a few drinks at the time.
chunkymunky
New Member
- Posts
- 9,901
- Location
- worcestershire
That reminds me I need to get them measurements lol
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
I might have been a bit ****ed if it was a weekend
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
I might have been a bit ****ed if it was a weekend
possibly was,but you offered to make them.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
haha would help
be easier for me to cut it on the band saw than for you to do it with a grinder!
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
possibly was,but you offered to make them.
PM me to sort something if you still want them then
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
