As its not something I use often, I usually borrow a mates when I need one. But I'm the kind of person who doesn't want to have to rely on someone else if possible, so thinking of buying one. His is an off vehicle one, but I would like one that does a good job on and off vehicle. Sykes Pickavant and Snap On (Blue Point) look good but expensive for occasional use. Might consider these if reasonable second hand. Can anyone recommend what I need firstly and what's worked for them. Cheers
Brake Flaring Tool
- Thread starter meego
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
JimS
Well-Known Member
- Posts
- 10,708
- Location
- Not far enough away from London
I changed the lines on an old car I was fixing up, I think I just got a cheap flaring set from Toolstation, it was cheap but did the job. Took a couple of practices to get it right (bubble flares) but once you have the knack the rest were all perfect
brian47
Well-Known Member
- Posts
- 8,867
No matter what or which flaring tool you get, the most important part of making a good flare is cutting the tube absolutely square and preferably without hacksaw filings. You'd be well advised to get a proper tube cutter at the same time and treat both tools, cutter and flaring tool as a kit. With a true end on the pipe, almost any flaring tool will produce acceptable results.
Don't bothér with the ****e ones from halfords, laserline etc. They tend not to flare straight. ended up getting this one which has been excellent: Amazon product
Flossie
Well-Known Member
- Posts
- 11,000
- Location
- Shropshire
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
steel pipes require special collets and a lot of pressure, i doubt you do steel pipes with most cheaper tools
- Posts
- 22,900
- Location
- In the next Glen
All this not flaring straight is bullsh!te I have used from the cheapest flaring kit available to snap on ones
& mine are perfect, if it flares squint you have too much pipe sticking out the end of the press & therefor it bends...........
After you have cut your pipe chamfer the end before flaring, just take the corner off it this will give you
a nice round flare every time
& mine are perfect, if it flares squint you have too much pipe sticking out the end of the press & therefor it bends...........
After you have cut your pipe chamfer the end before flaring, just take the corner off it this will give you
a nice round flare every time
Ordered one of these earlier today. I'll let you know how it goes. Cheers.
How do you chamfer it? With a file or what. Inside dia or outside dia ?All this not flaring straight is bullsh!te I have used from the cheapest flaring kit available to snap on ones
& mine are perfect, if it flares squint you have too much pipe sticking out the end of the press & therefor it bends...........
After you have cut your pipe chamfer the end before flaring, just take the corner off it this will give you
a nice round flare every time
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
just use a pipe cutter
Cheers James. Got one of those ordered too.
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
thats all you need
brian47
Well-Known Member
- Posts
- 8,867
+1 ^^^^^
As I said in post #3, use a tube or pipe cutter. That way you get an accurate square end, a slight chamfer on the outside of the end of the pipe and no metal filings like if you'd used a hacksaw or Dremel. After that it's just a case of setting the flaring tool correctly as @kevstar said in post #8.
The more you try to remove the very slight burr from the inside of the pipe after cutting, the more bits of swarf and filings you'll have to try to clean out before you use the pipe. The burr is so slight it won't affect anything if it's left alone.
vilguy
Do'er of stuff and the like
- Posts
- 9,915
- Location
- Dumfrieshire
I just use the cheap £10 one from ching Chong too
Worked for years with no issues
Worked for years with no issues
Pinch the hoover & use with the crevice tool.
I have a 'Henry' which is for garage use & bodywork (use it with Mirka abranet for sanding filler) so don't need to wait until Mrs R is out
brian47
Well-Known Member
- Posts
- 8,867
Pinch the hoover & use with the crevice tool.
I have a 'Henry' which is for garage use & bodywork (use it with Mirka abranet for sanding filler) so don't need to wait until Mrs R is out
That's OK for a new, clean, dry pipe, but what happens when you're flaring an existing pipe which has the residue of fluid in it, such as when making a repair by cutting in a new piece to replace a damaged length?
'I have a 'Henry' which is for garage use'.
Minor amounts of liquid have never bothered it.
The amount you're going to get out for a quick pass over the end is negligible. By the time you've finished cutting & flaring there's never much fluid left anyway. If you're really bothered then use a piece of cloth over the end of the crevice tool to absorb whatever's left. A Henry will easily suck through a bit of cloth.
Minor amounts of liquid have never bothered it.
The amount you're going to get out for a quick pass over the end is negligible. By the time you've finished cutting & flaring there's never much fluid left anyway. If you're really bothered then use a piece of cloth over the end of the crevice tool to absorb whatever's left. A Henry will easily suck through a bit of cloth.
Last edited:
brian47
Well-Known Member
- Posts
- 8,867
I wasn't worried about sucking out any fluid, I was more worried about filings and swarf being stuck in the fluid residue and being unable to clean it out after cutting. The last thing you would want is bits of metal working their way into a slave cylinder and damaging either the seals or worse still scratching the bore.
- Posts
- 9,105
- Location
- Roaming the UK on assignments
I don't bother, for the time it takes you might as well run a while new line and be sure, original pipes will be steel and if rotten/damaged the DIY kit isn't really strong enough to do ought, if it's a damaged cupronickel line then the small pipe cutter will make it clean cut and bevelled enough to get a decent flare on it under there.
