Freelander 1 1.8K lumpy start from cold.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
P

PRO

Well-Known Member
Posts
636
Location
West Yorkshire
Hi, me again.
I've noticed lately that when I start the car from cold, there is a heavy smell of petrol around and it runs lumpy for about 30 seconds give or take. Feels like a misfire but I can't see any logged in OBD.
Spark plugs are new (ngk iridium) and two coils are also new and genuine lr.
No visible smoke and runs very well afterwards.
I have very good diag any idea if I start it on what values I should look?
 
Actually I do have some values and errors. Says cat failure however the cat is brand new, therefore before I look into changing this quite expensive part, can a sensor cause this?


upload_2020-2-1_10-52-53.png

upload_2020-2-1_10-53-1.png

upload_2020-2-1_10-53-9.png

upload_2020-2-1_10-53-42.png

upload_2020-2-1_10-53-32.png

upload_2020-2-1_10-53-21.png
 
They were, I check and clean faults every week and this was not there last week.
Car is also lumpy so something is happening not just the sensor, I suspect.
 
yes it is, will check for fuel trim. Since the petrol smell, I am guessing there is fuel going in the cat.
At this point I will be looking on the o2 sensor, map sensor, exhaust leaks or anything that causes the ecu to overfuel on cold.
Would gladly accept any advise as well.
 
At this point I've replaced the remaining two coils. Symptoms are the same, nowhere near to fix.
Temp sensors are working fine.
I am starting to blame the o2 sensor, the pre-cat one. Any idea what values to test and how?
Car is not losing oil or coolant, runs fine after a min. Shaking on cold start.
 
Alright, replaced the Upstream o2 sensor with genuine bosch one. Things did improve as there is no more petrol smell on start.
However, still violently shakes for a minute or two.
Now, from time to time I can also feel it kicking on idle.

Replaced all these with genuine MG/LR parts, new:

Upstream O2 Sensor
All spark plugs
All Coils
52MM Throttle with new TPS
IACV valve
Air filter
Rocker cover

I am out of ideas at this point. Does the downstream o2 could for running or simply checks the efficiency of the cat?
 
PRO said:
Upstream O2 Sensor
All spark plugs
All Coils
52MM Throttle with new TPS
IACV valve
Air filter
Rocker cover
Click to expand...
That's covered pretty much everything, except the fuel delivery system. Have you checked fuel pump pressure and supply volume?
PRO said:
Does the downstream o2 could for running or simply checks the efficiency of the cat?
Click to expand...
Cat efficiency only. ;)
 
Indeed, did not touch the fuel system yet. I do have a new fuel filter.
Can I check any of these with delphi? I am tempted to replace the whole pump and filter (one on tank if it's the only one) since I am removing it anyway.
Somebody else told me it might be even the injectors... although these are quite expensive to replace. And labour intensive if I have to remove the inlet manifold for that...
Which does bring the question if replacing injectors require removal of manifold or can be done without? Got a extremely sweet auction deal on vdo pump :) will be changed regardless.
 
Last edited:
PRO said:
Indeed, did not touch the fuel system yet. I do have a new fuel filter.
Click to expand...
It's quite common for the filter to clog up.
PRO said:
Can I check any of these with delphi?
Click to expand...
No. You need to use a mechanical gauge on the fuel rail test point. ;)

PRO said:
I am tempted to replace the whole pump and filter (one on tank if it's the only one) since I am removing it anyway.
Click to expand...
Yes the pump is in the tank.
PRO said:
Got a extremely sweet auction deal on vdo pump :) will be changed regardless.
Click to expand...
Make sure you get the correct part number, or the fuel gauge will work backwards. :eek:
 
Changed pump, not much improvement. However now for some reasons shows full tank start from time to time.
Bit of a problem, I don't know how much fuel I have. It is intermittent.
 
Faulty fuel level sender which is part of pump assembly.

Return it for replacement. Or if you think your old one was OK just return it for refund!
 
Did you get the right pump/sender for the age of your car? As fuel gauge can work in reverse with the incorrect one.

Or the float arm maybe getting snagged in the tank
 
You must log in or register to reply here.

Similar threads

davidcarretero
Freelander 1 TD4 continues running after key removed
Replies
7
Views
964
davidcarretero
davidcarretero
Cr4zyChris
Freelander 1 Td4 failing to start, part missing?
Replies
3
Views
763
rpenyan
R
B
Cold start problems
Replies
19
Views
2K
kermit_rr
kermit_rr
davidcarretero
Freelander 1 TD4 continues running after key removed
Replies
2
Views
620
davidcarretero
davidcarretero
A
2.7 TDV6 Cold fault
2
Replies
32
Views
4K
Tjaan
T
Back
Top