Search results

if you ever bridgend way ,theres a lad there that keeps fully recovered headlinings,post covers ,you book a time he strips yours out fits new one ,keeps your old one . cracking job ,reasonable as well

2003 td6 l 322 . I'm getting air reservoit tank static when filling o my rs soloutions software . I clear and it comes back. it is however lifting on all four corners . it wouldnt lift properly and would lift two maybe 3 corners before compressor overheat used to come on so i replaced the seal...

most locksmiths get a bit tardy if they dont supply the blank so try to find an accommodating one . I but the silver flip type off flea bay for about 40 pounds . Have to buy a reader and copier for the bmw type ,take the ews module off follow their instructions and youll soon have working key...

go with the inline one,dont know what its like on yours but on the rover 75 ,same engine it is an absolute swine,engine mount on ,lift ,drop the engine and its still a swine to do as theres no room to get sockets spanners on ,just enough room to screw the bolts out 10 degrees re site the spanner...

dont know if its the same but just trying to help ,i had a small noise knocking ,which got worse and i thought the big ends were gone or the crank was picking up . with help off here it worked out to be the rubber dampening bush on the front crankshaft pulley . oddly the main give awsay in the...

still no luck im afraid ,i changed the piston seal as the compressor was cutting out on the overheat temperature probe. its working fine and recording 11 bar of pressure . the suspension lights have no changed . when it starts it says standard height but shes on the lower bump stops at the front...

May I ask what foxwell does that please?

Have you any update as mine is very similar Thanks

I wish it was ,I just started her after 24 hours and .....the right side has gone to standard but both the left hand front and rear have gone to high. The standard height light is flashing but the high led remains steady on . I used the rsw solution and it records no faults ! I used the rsw to...

Oh yes sits fine and I can use the rsw to adjust all four corners if necessary

2003 3rd 6 had it 5 weeks Hi all my high led is on all the time. Just changed the gearbox oil and had this happen. If I use the manual lift lower,access rotary it appears to lift to standard and high but the high light remains out when it tries to reach standard and the standard light keeps...

Super many thanks

I'm going to have a go but confused by the information I've read. I know that the actual values given off the rsw solutions interface don't relate to anything and are just that ,readings . Where can I find what actual real heights from wheel centers to vertical lip should be . E.g in mm Many thanks

It has the option to depressive the rear. When I select this it drops about 20 mm from full ride height and just sits there. Ot doesn't wont settle to the bump stops . Apologies for late reply had problems with my daughter in hospital

hi all just bought a 2003 td6 l 322 with 140,000 miles on the clock. Im having problems with the suspension namely the rear is way too high and the front too low. Whilst driving the "high" suspension light stays on ,i can turn the switch tonormal and some lowering occurs at the front but not at...

Did the work myself and all bolts were loosely fitted until wheels were back on floor Datatek,yep good idea I'll double check just in case one worked loose ,I'll probably disconnect ,spray with contact cleaner allow to dry and refit .many thanks to all

Hi all l 322 2004 vogue diesel 3 litre. Occasionally the air suspension bleeps when driving ,usually when I go over a bump . If I stop ,switch off,turn the steering wheel back and forth the sir suspension works again. It might do it again next bump or might last 100 miles . Air suspension works...

Many thanks to all Will a nanacom recalibrate the sensors ? If I change a sensor must they be calibrated to the motor or just a straight swap ?

Hi All Im Having problems with my 1999 p 38 bmw powered 2.5 manual . The problem im having is that the motor doesnt sit correctly . Ive put my nanacom on it and i get the following standard height stored...

Hi all Diesel 1998 p 38 All of a sudden ,when I get to drive ,shut the door,interior light goes off but the dash info keeps display the front door open. The girl starts fine but suspension won't lift as the warning messa ge .keeps showing Any help ,really appreciated