Search results

Rock the car while you're underneath the car with a hand on each of the joints in turn. You'll feel the play as it moves if there is any. Any play = possible knocking noise

It might be because the relevant brake manufacturer & Land Rover didn't believe people could be trusted to torque the relevant bolts correctly on what is obviously a very safety critical part. Bolts were probably tightened to just below the bolts absolute limit in the factory & shouldn't be re-used

After a bit of memory searching I remembered what I did with the Steering Wheel Controls wiring - as I found a Youtube video explaining that you ONLY need to connect the Key 1 and Ground wires - NOT the Key 2 wire, which is left unconnected. Assigning the various control functions is then done...

If you've had to turn up the head unit a lot to make it loud enough to hear, the head unit internal amplifiers could be working very hard - which might explain why it's getting hot. What % of max volume are you having to use ? As said, if fitted, the LR amplifier is located under the front...

Is it wired to play through the OE amplifier (if fitted to yours) & someone forgot to add the wire from the aftermarket unit to switch the amplifier on ?

I don't understand what you're asking ? You've said you've got it working already and you've got all the wiring diagrams identifying the relevant connections on the D2 and the Kenwood.

I think same style caps may have been fitted to Rover 200, 400, 600 & 800 type cars of a similar age. I did the same thing you're proposing quite a few years ago (Before I developed a helpful wife :)). I think I got the cap I adapted from a Rover 216. Beware there's a fair bit of work to make...

Anaconda, when I looked there were no suitable aftermarket cables to connect the pre-amplifier aftermarket radio rca / phono output plugs to the d2s din plugs to the d2s amplifier inputs. The din - din connectors are only suitable for a D2 base model without the separate amplifier. Paul

Those still sound like problems associated with the yoke & selector. I had similar restricted selections before I re-fitted the bush & lever. Did you check the selector rod / fork would move OK before you refitted the gear stick - to make sure it could move OK ? Maybe the missing bits of plastic...

Marc, the steering wheel control wires are in the grey big ISO plug on the D2. Pins 2 & 3. I think all I did was try each of the 2 Xtrons steering wheel control cables, key 1 / no 3 and key 2 / no. 5 with each of the LR cables to see which way round worked. It was then a matter of using the...

Yes. Just be sure that 900mm is enough ! I ended up going with a 1400 mm section & was glad I did when we cut off the rusty section which was remarkably dire even around the damper mountings which you'd imagine were a "high point" on the chassis & therefore not so prone to water staying inside...

I got a second hand spare top hose outlet & just drilled and tapped into the side of the flange to allow a sensor to be fitted. Same end result as the Gore item, but a lot cheaper

Next stop is losing all gears and leaving you stuck somewhere. Leave it a bit longer for the full experience 🤣

The smaller pistons improve the braking balance between front & rear & reduce brake pedal travel a minor amount.

You're not the first it's happened to :) I never found the missing circlip on mine & it's had a few oil changes since it fell in. Fortunately it's never caused any problems.

Firstly, is this about your Discovery 2 ? If not, what vehicle ? Secondly, the discs can't be scored by the caliper pistons - they should not be in contact unless the pads are missing. Are you suggesting that the rear drivers side brake pad has scored the disc ? New pads shouldn't cause any...

Maybe the D2 had more caster as standard than the D1. The D1 axle was RR Classic / Defender based, whereas the D2 changed to the CV type joints. I think most recommendations for the D2 do not include caster correction for 2 inch lift. You can add it, but it will be at the expense of making the...

You won't need 3 degree caster correction on the front with a 2 inch lift. That's only required for 3 inches and more. I've been running a 2inch lift with standard arms on our D2 for the last 10 years & it steers arrow straight on its own - without any self centering steering damper - just the...

Most of the wiring is fairly straight forward - just making sure you match the correct wires up - "simples" ;). The new head unit wiring is all clearly labelled, so you then have to get the wiring diagram for your car set-up (Harmon Kardon is slightly different to Lear I think) & work out the...

A few months ago I fitted an an XTRONS DQS112L head unit with 10" screen Android operating system & Android Auto / Apple car play, Bluetooth, screen mirroring & reversing camera (camera was extra) Definitely not as cheap as some Chinese units. Cost just over £300 in 1 of their relatively...