I'm staring at mine, mesmerised, having just brought my wife and neighbours back from the shops, and having taken a minor bend on a main road close-by - and almost lost it at 40 mph. Stopped immediately to find two rear nearside wheel nuts missing, the other three loose enough to be finger-tightened. I note one the studs has lost the top-half inch. Anyone ever had this problem or should I be looking at other causes? The wheel was last off 2013 when I had four new tyres fitted and all wheels were re-fitted with an air-gun. have checked the other three wheels and they are tight tight tight.
Have a good day.
 
Collected from Wicken 4X4 (just around the corner, literally) after they fixed the heater system (nothing worked, even the fan) and coded the radio, fitted new battery.
Now it is usable again.
 
Just got in after rewiring the rear lights and fitted a new light switch after the original switch went full short and filled the cab with plenty of smoke before I could hit the lol switch on the way back from the nationals. I guess 29 year old switch gave up the ghost!! Rear wiring was fubar'd so all replaced and sorted.

One ****er I couldn't find my heat shrink box so I will pick up some tomorrow and isolate the now soldered wires.
 
adjusted my rockers had nearly 2 mm clearance on no.8 hopefully that'll cure the ticking and the rough startup first thing and the sudden jolt on turn off and severe lack of power on first acceleration if not then think i'll be looking at the lift pump
 
put my disco in for works...
Welding; Arches, Seatbelt mounts, Boot panel

Brakes: Front disks and pie dishs

N/S/R Window lifter

Door locks x 3

and some other little niggley bits!
 
Just took mine for a short spin down to the village in the pouring rain. Have to say it is very noticeable the extra grip it now has since I fitted my new General Grabbers AT2's plus virtually no road noise in normal conditions but you can hear the spray being thrown up in the wet.
 
Started stripping the 90 in preparation for new swivels and a calliper overhaul, new seals and wheel bearings while I'm at it.
 
enjoyed the power that was missing before i set the rockers up this morning. so much safer to get out my road onto the main road
 
Great start to the day. Jumped in my Landy only to find I have no clutch. Pedal is up and has pressure but can't engage gears and once in gear can't get it out. No warning anything was wrong before. Any suggestions what it might be, my thinking is a new clutch.
 
Changed the rear dif flange and prop to a 200tdi with the UJ after a worrying drive to and back from France last week.

Welded a full boot floor in and a new rear wheel arch, also welded in some brackets to finally fix my d2 lights in securely.

Still have quite a bad oil leak coming from what looks like every seal on the tranny box!
 

Attachments

  • 1534822_10151852387806176_1222707252_o.jpeg
    1534822_10151852387806176_1222707252_o.jpeg
    224.8 KB · Views: 145
put it in for its M.O.T

came back with 13 months on it....just one advisory "rear shock rubber slightly worn..
happy day's.:clap2::clap2:
 
Started looking at the Landy for it's MOT and a few repairs...

Fixed boost gauge by removing a bent section of the pipe
Fixed gauge light to ammeter
Changed oil & filter
Replaced the two rear shocks
Found 5 small holes which can be sorted tomorrow with the steering box.
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
551
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
650
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
932
Knappster
Knappster
Mooky
Replacing thermostat
Replies
14
Views
605
Mooky
Mooky
I
Re-coding of ABS Module after repacement
Replies
10
Views
1K
invisible999
I