RangeRoller dt said:
Mine was unbelievably slow to start with. Can see why people say they are a slug. Bit of TLC is all they need they weren’t like that leaving the factory.
Click to expand...

Exactly i think the modulation makes a lot of difference to the power, as mine was getting slower not that you notice it as its so gradual till i tapped the pump in a bit to take up the chain stretch and whoosh off she goes like a rocket and the sound of that straight 6 is lovely:D
 
Discovered the MAF and IACV were covered in crud. So cleaned them both.
Cured the source of the smoke - the heat padding and the PVC underseal stuff above the passenger CAT had given way and were resting on it. Ripped all that off and will get the garage to replace when they have him on the ramps for the MOT.
Started him, much smoother and more responsive, quieter. Really shows up the EAS compressor being worn out.
He pumped up OK on all corners (was a bit worried about that after sitting for 5 months), went into low OK and crept eagerly 2 feet back, 4 forward and 2 back again.
Wife will do some inside fettling, and I need to sort the poxy boot release AGAIN! but otherwise he is now MOT ready so take him there Tuesday so they can sort the bits and MOT on Thursday. Unless they get a cancellation and get him in sooner.
Looking forward to pouring some pricy unleaded in there again!
 
Last edited:
Remembered I had this old bluetooth car kit with music streaming from a previous car so hooked it up to an FM transmitter and it works a treat on the bench.
Pairs up with 2 phones at the same time as well so great for work and private mobile :D

upload_2021-12-12_21-42-20.png
 
brianp38dse said:
Exactly i think the modulation makes a lot of difference to the power, as mine was getting slower not that you notice it as its so gradual till i tapped the pump in a bit to take up the chain stretch and whoosh off she goes like a rocket and the sound of that straight 6 is lovely:D
Click to expand...
Getting the modulation on the project car spot on made a big difference to performance, starting and engine sound.:D
 
I’ve had loads of parts of them no problems even replacing wrong parts I had ordered great coms through email for correct parts for my car as well
 
domino said:
If you need anything feel free to have it sent to me and I'll drop it in to you next year when I'm passing again :)
Click to expand...
That's very kind. However as things stand at the moment, you would likely be stung for duty at the crossing, the French are being very obstructive at the moment. I'm sure it will all settle down in time.
 
Datatek said:
That's very kind. However as things stand at the moment, you would likely be stung for duty at the crossing, the French are being very obstructive at the moment. I'm sure it will all settle down in time.
Click to expand...
I've heard they are stinging bikers who van their bikes to destination instead of riding
 
Flossie said:
I will:cool:
Going to grind a little off opposite sides, try ,and repeat as necessary so it just slips on.
The joints look drier than the Doris's Xmas turkey so I'm keen to get it done as there is no play in them.
Click to expand...
I had to do both sides.
 
You must log in or register to reply here.

Similar threads

A
Range Rover L322 - not turning over
Replies
12
Views
2K
gold rover
gold rover
B
L320 range rover sport 3.0 tdv6 loosing power steering fluid
Replies
3
Views
533
Mark Piercy
Mark Piercy
F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
1K
Grrrrrr
Grrrrrr
T
Non start
Replies
3
Views
717
Datatek
Datatek
T
Fan Clutch??
Replies
14
Views
799
Grrrrrr
Grrrrrr