P38A WTF just Happenned?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Take a picture with your phone. Helps people here visualise the issue.

Make sure you put the right coolant in as they don't mix. If overheating check the viscous fan first, then the water pump and stat.
 
Space bars are useful items. ButwhencommentingonpoliticalcontentinAGitisbettertojustwritewhatyouhavetosayandletthereaderdecidewhatyouactuallymeanandjustsupplyingsomepunctuationtoaidthatfunction. Eg ,,,,,,,,,,,,,,,.............."""""""""""""??????!!!!!! Etc. :D:D:D
 
Wazzajnr said:
Did you apply FBH101 to aforesaid fat thumbs or phone keyboard??? Makes a difference you know :)
Click to expand...
At first I applied it to the fat thumbs...then I noticed a nasty rash had formed so went to the doctors, he said I should stop having sex with monkeys.....I thought about this for a while and decided I could live with the rash as the monkeys say they love me, so I liberally applied the FBH101 to the keyboard instead and so far the spacebar problem is OK, but my rash has spread...still it could be worse! :D:D:D
 
I imagine Mr Rust had a hand in this! If the car hasn't been on the bump stops for a few years, I would imagine the sensor brackets had weakened and a sudden drop followed by driving over rough ground has killed it. I haven't looked under mine yet, perhaps I too have bits hanging off after that stupid road on Saturday :confused:

I'll be taking photo's to see how the re-programming goes. If you look at the thread Arghhhhh. All At Once, you can see the fun I had last week and how I dealt with it until I got the pump fixed and the software to get it off the hard stuff...
 
Iainl123 said:
I haven't tried the compressor filter trick, will have a play it seems a strange coincidence to me go have had one corner drooping earlier today, and then the eas flipping out totally and then find the drooping corner sensor hanging off. also the front raised and held level so I'm guessing the compressor is working properly?

As a side not what amount of engine coolant needs to go into the coolant system? I'm thinking of adding waterless coolant as she seems to be getting warm and I think it might be worth a try.
It will only mask a problem,find out why it is running hot?...Or warm?
That is again all,

Iain.
Click to expand...
 
Hi all,

sorry its been a while since I updated the post..... so I had a new sensor ordered, and I have fitted that to replace the old broken one this afternoon; I got a data cable and the EAS unlock software and all seemed well, the car rose and shifted through the suspension settings as it should, but I really struggled to figure out how to calibrate the settings.

I had managed to clear the 35mph warning and the EAS lights had returned to normal. I took the car out for a drive, it was riding high but she hunkered down into highway mode etc so I thought I just needed to adjust the EAS height settings. Then, after 36 miles the EAS fault error came back, but no 35mph warning and the car remained on suspension and not bump stops.

Ive gotten home and plugged in the EAS software and I, hoping that someone mght be able to help me out with the settings and error code as I'm baffled!

the only error code that I get is 6. RR reading incorrect this is the ride height sensor that I have replaced.

I have input the following values in to the calibration tab - I know that they have written correctly as are displayed in the boxes after pressing the GET ALL button

FR FL RR RL
High 156 156 147 147
Standard 123 123 109 109
Motorway 107 107 107 107
Access 70 70 75 75

when in access mode the actual height measurements (centre wheel to centre arch) are:
FR 390MM
FL 410MM
RR 430MM
RL 430MM

when in standard mode the height measurements are:
FR 420MM
FL 430MM
RR 520MM
RL 510MM

So none of the figures seem to correlate, I cant seem to figure out the actual real world MM value of the EAS ride height calibration input values.

When I use the get height setting, the corner values are displayed as.
FL 70
FR 64
RL 99
RR 17

I have no idea where to go from here, and any advice would be greatly appreciated!!

Iain
 
OK, the values are just the full travel spread across 255 counts so don't relate to any measurements.
The rear right reading 17 is completely wrong so I suspect a wiring issue or faulty sensor. Was this the one you replaced? If so, was it a genuine Dunlop one? Also, was it the correct one. On early models they are handed but not on later models.
 
You also are better using setting blocks than measuring to the arches as you can't really get it wrong then. That said, if there's a sensor not reading correctly it will never work.
 
this is the sensor i have fitted

Rear Right-hand Height Sensor 94-97 STC3593AA
STC3593AA.JPG
 
OK, the lengths are in wammers post in the technical archive https://www.landyzone.co.uk/land-rover/checking-eas-compressor-and-diaphragm-valve.172555/
I used some 28mm diameter wooden broom handle and just bound the ends with tape to make them stay in the bump stops.
Lift the suspension up to extend height, insert the blocks into the bump stops then drop down to access height. This will mean the axle is a fixed distance from the chassis. You then read the values in from the sensors and write that value into the ECU memory. Only thing is, these numbers must be within certain limits or the ECU will default to fixed values
 
You must log in or register to reply here.

Similar threads

Montyjohn
P38A Adding a valve to manually fill EAS tank and why did my pump fail again?
Replies
14
Views
937
Datatek
Datatek
K
Is my RR Classic in EAS shutdown?
Replies
12
Views
855
kevleaper
K
R
L322 gearbox problem 2010 TDV8 Vogue
Replies
11
Views
445
roythebus
R
Flossie
P38A Eas issues
2
Replies
22
Views
1K
Datatek
Datatek
ar1g3
P38A P38 rattle at idle
2
Replies
26
Views
3K
roythebus
R
Back
Top