Won’t start

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
guineafowl21 said:
Won’t even fire on easystart? That sounds worrying, but I find it gets lost in the long intake path. Make sure you’re spraying it right into the manifold, right at the EGR.

Do you get a rev counter reading when cranking? Could be the crank sensor if not.
Click to expand...
Yes that’s where I was spraying it, I’ve put a new crank sensor on it. The machine I got won’t read fuel pressure or anything
 
Update

Bought icarsoft scanner i930

Cleared codes and re run test.. no faults found, car still won’t start, all original parts returned. Will start on easy start now but cuts out when easy start runs out.
 
I know youve already been there but the cam sensor is only used to set up the timing on startup, but not used after that whilst its running.
May be worth checking the wiring for continuity to the ecu from the sensor plug with the ecu disconnected.

Just changed cam sensor in mine for non - start fault would spin over on the starter but no injection, which appears to be where you are at present, and it doesn't always set a fault in the ecu !!
 
Have I got this right?

Engine starts on Easy Start but won't start / run normally so it is not injecting fuel.
This means that either you don't have a high pressure fuel supply or the ECM is not triggering the injectors
If the rail pressure sensor or its wiring was damaged then the ECM would substitute a default value and the engine should start.
Engine stopped when running so not the cam sensor and you have changed crank sensor so the ECM should know where the crankshaft is.
You have eliminated the HP pump so not that and you changed the fuel pressure regulator with the pump from a known working engine - should be OK.
Can you put a fuel pressure gauge on the high pressure fuel line to check that the HP pump is running?
If that is all OK then we have the low pressure fuel system - if the ECM does not think that the low pressure fuel is coming through then it will shut down the HP pump.
LP pump is priming so not the pump relay or the inertia switch but is there pressure at the inlet to the HP pump?
Could the LP fuel sensor be faulty / disconnected?
When you changed the fuel filter did you run the LP pump? - I remember a recent thread on LZ where somebody found a foreign body in the fuel line that was restricting flow.

Can't think of anything else for now but without some fuel pressure readings this is going to be largely guesswork
 
Sblendid said:
Update

Bought icarsoft scanner i930

Cleared codes and re run test.. no faults found, car still won’t start, all original parts returned. Will start on easy start now but cuts out when easy start runs out.
Click to expand...
Were there any codes?

Can you get some live data readings - fuel pressures etc?
 
blodge said:
Have I got this right?

Engine starts on Easy Start but won't start / run normally so it is not injecting fuel.
This means that either you don't have a high pressure fuel supply or the ECM is not triggering the injectors
If the rail pressure sensor or its wiring was damaged then the ECM would substitute a default value and the engine should start.
Engine stopped when running so not the cam sensor and you have changed crank sensor so the ECM should know where the crankshaft is.
You have eliminated the HP pump so not that and you changed the fuel pressure regulator with the pump from a known working engine - should be OK.
Can you put a fuel pressure gauge on the high pressure fuel line to check that the HP pump is running?
If that is all OK then we have the low pressure fuel system - if the ECM does not think that the low pressure fuel is coming through then it will shut down the HP pump.
LP pump is priming so not the pump relay or the inertia switch but is there pressure at the inlet to the HP pump?
Could the LP fuel sensor be faulty / disconnected?
When you changed the fuel filter did you run the LP pump? - I remember a recent thread on LZ where somebody found a foreign body in the fuel line that was restricting flow.

Can't think of anything else for now but without some fuel pressure readings this is going to be largely guesswork
Click to expand...
Just forwarded all this over to my mate who is doing it, thank you butty
 
****UPDATE***

Started back with original parts.
Got the diagnostic working. No pressure on fuel rail. Can't do leak test until we get pressure. Pump is working. That leaves wiring fault. Stripped out the loom and tested with no faults. Do you think the pump chain could of snapped?
 
****UPDATE***

Started back with original parts
Got the diagnostic working. No pressure on fuel rail. Can't do leak test until we get pressure. Pump is working. That leaves wiring fault. Stripped the loom out and tested no faults. Do you think the pump chain could of snapped
 
Nodge68 said:
Have you changed the pressure regulator O rings? That's what it sounds like to me.
Click to expand...

I agree completely, I had exactly the same issues as the OP and changed everything and more. The HP pump was recon so I didn't consider it could be faulty. Changed the seals on the regulator off the old pump and put it in the recon pump, started straight away, which was actually quite disappointing considering I'd spent nearly a grand in parts and God knows how many hours fitting them to find 3 quids worth of seals and an hour fitting them fixed it...
 
You must log in or register to reply here.

Similar threads

A
A loose bolt on CAM sensor
2 3
Replies
44
Views
3K
Arctic2
Arctic2
Freddie17
Freelander 1 Cam shaft sensor
Replies
4
Views
916
Freddie17
Freddie17
O
Series 2 won’t start!! Help!
Replies
5
Views
656
brianp38dse
brianp38dse
O
Series 2 won’t start! Please help xx
2
Replies
32
Views
2K
pabloako
pabloako
G
None starting discovery td5
Replies
0
Views
556
gary dhenin
G
Back
Top