Bobsticle
De Villes Advocaat
- Posts
- 27,632
- Location
- Manchester
I am a Doctor
Which Exhaust
- Thread starter border
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Iirc there is/was an issue with hearing loss and stainless exhausts? Think to do with the tone due to the stainless being so thin.
Got stainless on my 90, was on car when I bought it ten years agp, covered in surface rust but still sound
Got stainless on my 90, was on car when I bought it ten years agp, covered in surface rust but still sound
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Found the kit but it is for SWB, will also have to check if my manifold has 3 or 4 holes, Exhaust Fitting Kit - RHD - Paddock Spares
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
Philosophy or Divinity?I am a Doctor
Bobsticle
De Villes Advocaat
- Posts
- 27,632
- Location
- Manchester
You may only need the copper gasket. The rest should come with the exhaust.
Even then the gasket won’t go on a crush pipe. These just pull onto the manifold and seal on the rounded end of the exhaust.
Have a look if your manifold has a rounded recess where the pipe sits.
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
I think there is a hearing loss issue with Series in general.
I don't much care, I am half deaf already. More worried about my back, and my sciatica!
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Will have to check it tomorrow, think it is rounded though
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
3 bolt on that one. Use plenty of exhaust paste. Eases assembly, and makes sealing up more likely.
Bobsticle
De Villes Advocaat
- Posts
- 27,632
- Location
- Manchester
I seem to remember the four hole flavour are a side fitting. The three hole are bottom fitting like the diagram on the paddocks site.
Oh and I also used a smear of paste on the joints.
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Bobsticle
De Villes Advocaat
- Posts
- 27,632
- Location
- Manchester
Yea. It looks like the standard three stud bottom fitment.
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Yes think so to, have emailed them to see if brackets ect are included, or might try and find one somewhere else that does include them.
Bobsticle
De Villes Advocaat
- Posts
- 27,632
- Location
- Manchester
It deffo ain’t one of these
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
See the top bit on this pic,
Attachments
Bobsticle
De Villes Advocaat
- Posts
- 27,632
- Location
- Manchester
Oh, and make sure that dip stick tube is tight down.
1/4 inch high and the oil measures wrong.
1/4 inch high and the oil measures wrong.
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Think it is Mate, I put about 7 litres of oil in and its showing right on the mark on stick.Oh, and make sure that dip stick tube is tight down.
1/4 inch high and the oil measures wrong.
Bobsticle
De Villes Advocaat
- Posts
- 27,632
- Location
- Manchester
Cool. Mine had a copper washer so had to be wound right down to the block.
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Paddocks don't seem to sure as to which will fit from these Land Rover Series 2, 2A and Series 3 - 109 inch Mild Steel Full Exhaust Systems - Paddock Spares If they don't know I aint got a clue
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Under seat
