What have you done to your Landie today.

a2dds · Dec 30, 2015

Today it broke... no surprise there then.

Wonder if one of you can help me

Got a disco transfer box on the back of an LT77 gearbox. Been running fine for 9k miles. But after an offroading trip recently it died today ( i think).

It has a habit of leaking all its fluid out, the box wasn't perfect when it went in. So i have a sneaky suspicion that a bearing has given up. When the gearbox is in neutral and transferbox is in gear (which is difficult to do), it roles forward and power is sent to the wheels. When the gearbox is in gear, any gear it doesn't matter, the whole things locks up and it stalls. No power gets passed the transfer box.

Does the gearbox output shaft spin when its in neutral? seems odd that it has power to the wheels when the gearbox is in neutral but totally locks up when its in gear.
Getting the transferbox in neutral and engaging the clutch it rattles like a pig (and sounds like there is a slight load on the engine), force it into gear while there is drive to it and it locks up and stalls.
Think i need to change the transfer box anyway, but does anyone know what this might be? And if its gearbox related instead?

why do the heavy things have to break.

Cheers, Adam

a2dds · Dec 30, 2015

Oh and I cut of a rusty outrigger and welded (badly), a new one on. As

ivancrx · Dec 31, 2015

Fitted 110 vented discs, pads and callipers to it and bled the brakes, fantastic stopping now

greyhair · Dec 31, 2015

Getting ready to fit my replacement bulkhead,

Animal88 · Jan 1, 2016

Found that I had a disappearing clutch pedal yesterday so tried bleeding it up and got a good pedal. Went laning and it gradually got worse and worse to the point that I had to rev match to change gear. I have now changed the slave cylinder with another I had laying about and got it bled up real nice. Haven't had a chance to test it out yet though but no doubt that's for tomorrow. While I was out laning my diff locks linkage fell to bits. The little bar that links from the bottom of the pivoted bar from the stick to the plate on top of the transfer box has snapped just enough to make it jump out so I now can't select diff lock without getting under with a spanner. Does anyone know where to get this little bar from. I have done the usual evilbay searches and not found any of the linkages for the lt230 in my 200tdi D1

jamesmartin · Jan 1, 2016

try ftc3698 and 2 x ftc3674

Animal88 · Jan 2, 2016

Yes thank you ftc3698 is the part in after cheers that'll save a lot of messing about trying to make something fit

Animal88 · Jan 2, 2016

I've also managed to find the clips now with the codes thanks. I was planning on hoping a tent peg could be shaped to fit then use my dremel to cut grooves to hold e clips to stop it jumping out

defenderdog · Jan 3, 2016

Cleared the crap from around my semi rebuilt Landy in preparation to carry on from where I left off about July last year. Must have it done by September this year or I'm giving up and selling up

Roaming Wombat · Jan 3, 2016

Discovered me roof leaks like a fooking sieve and not just the sunroof. Looks like its gong to be a roof off and on with some silicone seal in between job in the spring. Too damn wet to do it at the moment.

Vinlander · Jan 3, 2016

Roaming Wombat said:
Discovered me roof leaks like a fooking sieve and not just the sunroof. Looks like its gong to be a roof off and on with some silicone seal in between job in the spring. Too damn wet to do it at the moment.

Usually cures underwater.
True story.

Coffeelandy · Jan 4, 2016

Cleaned underneath after getting stuck and located the leak in my pas system.

bettsy64 · Jan 10, 2016

Roller paint job and finally got the fueling sorted on a newly fitted 200tdi

steveo · Jan 10, 2016

Pulled out the wiper motor and cable, spun the wheelboxes 180 degrees and refitted. Nice quiet wipers now

Took longer to get the trims back on than it did to sort the wipers!

elliot0850 · Jan 10, 2016

Not all today but this week i
Replace front prop
Replaced brake servo
Tie raped cables under dash
Welded rear axle trailing bracket
Welded rear shock mount
Welded rear crossmember
Wired low brake pad warning light

Not far off ready for the Peak District.

a2dds · Jan 12, 2016

Over the last week. Took out me transfer box and gear box.

Found a replacement gear box with very little wear on the output splines, changed the output oil seal. And now ready to stick it back in.

Looking forward to driving her again! Being in the work van is a pain in the bottom!

Roaming Wombat · Jan 16, 2016

Gave my trailing arms a paint ready for pressing in some new (poly)bushes

potus · Jan 16, 2016

Treated it to a wash and oil change after passing the MOT

simonm15 · Jan 18, 2016

Quite a productive few hours on Saturday! Fitted new battery to replace one that has died in the cold, fixed heated seat wiring, fixed exhaust rattle (front and mid sections weren't even close to being coupled together, so re-aligned and re-tightened clamp), replaced the rusty wing top vent screws with s/s ones, and re-fitted radio aerial cable that had come out back of stereo (had to take out Raptor dash to access it).
Also fitted some Xmas presents - Raptor glovebox, Climair wind deflectors and rear recovery point.

FlyingPete · Jan 19, 2016

Made a start on curing the wayward rear-wheel steering. Took the trailing arm off one side and found a large amount of play in the the bush at the chassis end. Got some new bushes waiting to be fitted, but need to get hold of a press or other means of taking the old ones out...

What have you done to your Landie today.

Active Member

Active Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Active Member

Active Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Member

Attachments

Well-Known Member

Active Member

Active Member

Well-Known Member

Well-Known Member

Member

Well-Known Member

Similar threads