Headtester
Active Member
- Posts
- 581
- Location
- Ruislip
Decided that I need a new front hub as the existing one is grumbling too loudly to ignore. Went from a little rumble every now and again to a "can't drive it" noise!
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
discodrivercumbria
Well-Known Member
- Posts
- 3,317
- Location
- South lakes
so did i!! but mine just undid changed bulb hey presto all is ok again,Changed headlight bulb (fixed broken fixing drilled and tapped top two holes all for a headlight bulb
For the love of LR's
osram night breakers!! crap! havent lasted long at all,
looking into changing headlights, new for old, part no XBC000811 cannot find which light it is!!!????
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
sp00k
Well-Known Member
- Posts
- 1,530
- Location
- Washington, County Durham, UK
Looks smart, how did you prep and paint it?
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
I sanded down the whole car and fixed the small bits that I could without going to far as it is a land rover
. I then primed it and sprayed it but with the bad weather of recent did have much time to paint the black bits but now is all done. Waiting for a few bits like new mirrors so not long till I'm back out in it.
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
Looking good now Danny!
Black bits are nice and shiny
Cheers mate have been having the same problems as you have with that recent bad weather we had but glad it's all done now.
got under it to belt the handbrake drum with a copper hammer. think yesterdays puddle splashing had got some water in it that had froze solid during the night had to go to low range to get it to move the first time then it did it again so used a copper hammer to persuade it to release properly. glad I'm picking up the new handbrake shoes and fitting kit tomorrow. think its needed before i have further problems
taylorslandy72
Active Member
- Posts
- 224
- Location
- bristol
Preparing the chassis for welding "once again"
Westwood8055
Active Member
- Posts
- 896
- Location
- Liversedge, West Yorkshire
Dropped it off for its mot knowing it's going to fail crapping myself waiting for the call to state cost of repairs and the inevitable fail word
crapping myself waiting for the call to state cost of repairs and the inevitable fail wordKlm2
New Member
- Posts
- 65
- Location
- County Durham
Just changed the water temp sender and the injector Harness. And the award for bright idea of the decade goes to the NUMPTY who designs an engine with a wiring harness running under the rocker cover...
Doh...........
Doh...........
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
Fitted MUD LED lights all around. Very pretty and very bright! Much clearer, sharper and just nicer than the regular lights.
Sadly upon fitting realised my brake switch has broken...
Sadly upon fitting realised my brake switch has broken...
need to get the new handbrake shoes and fitting kit fitted the constant bang as I try to drive away is getting annoying. need to adjust the headlight aim aswell hope that will improve my visability I think they are too high so I'm not getting the beam pattern on the road so I can't see. is there anything else that people have found helps with the headlights? D1 300tdi lights on a 200tdi
Check the voltage your getting to the bulb as old oxidized connectors in the system reduce the voltage that gets to the bulbs.
Check battery voltage and if you have much of a drop at the bulbs it's time to run the lights off a relay.
This should tell you more about it
Daniel Stern Lighting Consultancy and Supply
- Posts
- 83,279
- Location
- Embasinga stocæ
bigvinnie
Active Member
- Posts
- 748
- Location
- Catterick North Yorkshire
Took it for MOT and it only failed for r/h outrigger. Requires patching. First welding its had. So in tomorrow for a patch and its retest.
Quite happy really was expecting a few other things the garage clearly missed!
Quite happy really was expecting a few other things the garage clearly missed!
cheers for how to check I'm planning on doing the relay mod anyway it's just getting the time to do so.
any idea why my high beam tell tale is dimly lit with the dip beam on?
