nick2303
Well-Known Member
- Posts
- 4,255
- Location
- Leeds (not by choice)
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
joe1972
Well-Known Member
- Posts
- 1,595
- Location
- Manchester
Fitted a new rear wheel bearing. Was quite alarmed to find so much clay mud where the bearing should have been!
Hate doin wheel bearings, but has to be done...especially when the noise from the knackered one actually drowns out the noise from the cherry bomb exhaust!!!
Hate doin wheel bearings, but has to be done...especially when the noise from the knackered one actually drowns out the noise from the cherry bomb exhaust!!!
joe1972
Well-Known Member
- Posts
- 1,595
- Location
- Manchester
mikescuba
Well-Known Member
- Posts
- 2,731
- Location
- France, Loire, Rhone Alpes
According to the LR manuel for 750X16 in psi is 28 front and 48 rear for normal driving conditions. For Emergency soft 16 front 16 rear unladen loaded 16 front and 23 rear
This is for a 110.
This is for a 110.
nick2303
Well-Known Member
- Posts
- 4,255
- Location
- Leeds (not by choice)
48psi?
that seems high....
might help with the rediculous roll though...
cheers..
that seems high....
might help with the rediculous roll though...
cheers..
nick2303
Well-Known Member
- Posts
- 4,255
- Location
- Leeds (not by choice)
after doin a full injun rebuild ya complain bout swoppin a poxy wheel bearing... its a 15min job....
doin it takes less time than complainin bout it!! man up!!!!!
mikescuba
Well-Known Member
- Posts
- 2,731
- Location
- France, Loire, Rhone Alpes
That's what it says in the Land Rover Hand book for a 110.
joe1972
Well-Known Member
- Posts
- 1,595
- Location
- Manchester
Yeah I know...its not difficult...it's just one of those jobs I love to hate...and complain about
waldershelf
Well-Known Member
- Posts
- 2,397
- Location
- In the hills north west of Sheffield
Err OP said he had a tube in it
it might be a leaky valve but "seatin' an't got now't to do we' it" (that's Yorkshire speak)
Langers
Well-Known Member
- Posts
- 3,162
- Location
- Kent or Shropshire
Had a general maintenance sesh this afternoon, tightened up the steering box, what a difference! Also tightened a front wheel bearing (no more clunking), and tightened the fan and alternator belts (no more squealing). Lots of tightening.
Tomorrow's plan is to take off my 265s to sell them, and put back on the old 7.50s, in preparation for getting my 35s
Tomorrow's plan is to take off my 265s to sell them, and put back on the old 7.50s, in preparation for getting my 35s
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Set off the SRS by mistake so gotta get that fixed tomorrow and fit the bullbar seeing as I've finished covering up the rust on it…….plus it was soaking today
garfie
Member
- Posts
- 97
- Location
- South Wales
Took my daughter to her dancing / singing lesson and ended up having to get her to donate her pretty purple tights to make a fanbelt to get us home!
mikescuba
Well-Known Member
- Posts
- 2,731
- Location
- France, Loire, Rhone Alpes
All this gale force winds and driving rain has cleaned my Defender up a treat.
brendan 26
New Member
- Posts
- 3
- Location
- whitchurch shopshire
took its chassis in to be hot galv dipped
DEFENDER90-DAZ
New Member
- Posts
- 3,239
- Location
- Scotland - Houston
Fitted my ibm thinkpad (on laptop mount)for gps
Installed 4 gang cig plug extension
Installed 4 gang cig plug extension
