What have you done to your Landie today.

Thor1950 · Mar 3, 2013

can anyone find a pilot shaft for doc on E bay they cna't be more than 2-3 quid and he will need one again. needs to quiet being a cheap fooker. that v8 will has rusted stuck od rings will set up by the time this thing runs.

Fook the Royal Bath and West will of come and went before this thing goes.......... vroom vroom

Dr_evil · Mar 3, 2013

I borrowed the kit from the local mechanic, he's been using it for the last 50 years and you can tell

very battered looking

Thor1950 · Mar 3, 2013

Dr_evil said:
I borrowed the kit from the local mechanic, he's been using it for the last 50 years and you can tell very battered looking

Did he have the same problems as you???????? If it worked for him why not for you??????????

Think some one said to but it all together on the ground, motor, transmission then put in............. Wait a old fooker mentioned that

Dr_evil · Mar 3, 2013

Thor1950 said:
Did he have the same problems as you???????? If it worked for him why not for you??????????

Think some one said to but it all together on the ground, motor, transmission then put in............. Wait a old fooker mentioned that

He said he's had to take some apart again so I presume yes would be the answer and I was going to do that but there's not enough space. I did try before settling on in as two parts

Thor1950 · Mar 3, 2013

Dr_evil said:
He said he's had to take some apart again so I presume yes would be the answer and I was going to do that but there's not enough space. I did try before settling on in as two parts

if a motor can not go in as a unit there is something not right. You had the whole front end off should of been a straight shot

blue beasty · Mar 3, 2013

Dr_evil said:
He said he's had to take some apart again so I presume yes would be the answer and I was going to do that but there's not enough space. I did try before settling on in as two parts

Even using an alinement tool I always double check by eye, a long reach socket or similar and a good eye will tell you whether your within a gnats whisker or not.

suew · Mar 3, 2013

OK, this is "I might do this to my Landy today"

I have bought some Jate rings for my Defender. For the front as it has a towbar on the back.

Where do they go ?

Do they replace the rings which you can only use to tie things down. If so will they fit through the holes that are already there.

I might not attempt this if its not a simple job, but it looks easy enough, just one bolt

Oh and I did search but there is not a thread on this

Dr_evil · Mar 3, 2013

Thor1950 said:
if a motor can not go in as a unit there is something not right. You had the whole front end off should of been a straight shot

Yes but without having a long reach crane.......

Dr_evil · Mar 3, 2013

blue beasty said:
Even using an alinement tool I always double check by eye, a long reach socket or similar and a good eye will tell you whether your within a gnats whisker or not.

Yeah should have done but oh well. Next time will hopefully have an old shaft that's been cut down

jamesmartin · Mar 3, 2013

suew said:
OK, this is "I might do this to my Landy today"

I have bought some Jate rings for my Defender. For the front as it has a towbar on the back.

Where do they go ?

Do they replace the rings which you can only use to tie things down. If so will they fit through the holes that are already there.

I might not attempt this if its not a simple job, but it looks easy enough, just one bolt

Oh and I did search but there is not a thread on this

yes

suew · Mar 3, 2013

jamesmartin said:
yes

Thank you

Andytats · Mar 3, 2013

Finished all the welding on the rear bumper it just needs painting now

BECDFA57-97A9-45D1-A025-7A75BEB71A8D-1213-0000010D1B3D041A.jpg

09EBC633-D058-41EF-BF60-A9BD9DA7A02A-1213-0000010D29D7DF47.jpg

Thor1950 · Mar 3, 2013

Dr_evil said:
Yes but without having a long reach crane.......

what type of engine crane you have?????????? if you used one that could put the motor in, why could the transmission not be fitted to the motor??

charliemopic · Mar 3, 2013

Replaced leak off pipes and meant to replace the lift pump but only have a 1/2" drive oooooeeerrrrr.

Dr_evil · Mar 3, 2013

Thor1950 said:
what type of engine crane you have?????????? if you used one that could put the motor in, why could the transmission not be fitted to the motor??

Short one. The arm isn't strong enough to do both engine and box at the length it needs

200tdi ayre · Mar 3, 2013

Andytats said:
Finished all the welding on the rear bumper it just needs painting now

Planning on reversing through walls ?

stutab · Mar 3, 2013

200tdi ayre said:
Planning on reversing through walls ?

Breaking hard when talegated

Thor1950 · Mar 3, 2013

Dr_evil said:
Short one. The arm isn't strong enough to do both engine and box at the length it needs

Doc if it is long enough to but motor in then it will work with trans on. if it is tail/trans heavy, you use a small ratchet strap to level it out to put in. It is very easy to put it all together

goonarmy · Mar 3, 2013

Decided the fuel tank is impracticaly small

Dr_evil · Mar 3, 2013

Thor1950 said:
Doc if it is long enough to but motor in then it will work with trans on. if it is tail/trans heavy, you use a small ratchet strap to level it out to put in. It is very easy to put it all together

It's 250 kg at middle length and 150 at max length. Engines already at 230 so it won't take the extra strain. It's all sitting on a builders board now so level. Put it under engine and box with it sitting on axles and crossmembers to take the weight

What have you done to your Landie today.

Well-Known Member

Banned

Well-Known Member

Banned

Well-Known Member

Leaks an prone to bits dropping off

Well-Known Member

Banned

Banned

Well-Known Member

Well-Known Member

New Member

Well-Known Member

New Member

Banned

Well-Known Member

Well-Known Member

Well-Known Member

Beer tester

Banned

Similar threads