gotoneatlast
New Member
- Posts
- 3,431
- Location
- berkshire,uk
removed front and rear propshafts
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
flash42
Active Member
- Posts
- 739
- Location
- moretonhampstead, devon
drove the 90 up to surrey and back from devon.
350 mile round trip roughly and didnt miss a beat, apart from the lack of heating but that was already dead lol
coldest journey of my life lol
350 mile round trip roughly and didnt miss a beat, apart from the lack of heating but that was already dead lol
coldest journey of my life lol
- Posts
- 44,865
- Location
- Hornchurch
nowt, spent the last few dyas eating and drinking far too much.Not back to work till the 5th so should go out laning and find out what that knocking is coming from the left rear.....
bustersbus
Well-Known Member
- Posts
- 13,755
- Location
- Near Dumfries, Scotland
Ah've cleaned all the 'one-shot' grease from me disc, hub. swivel housin' etc!!!!!
Just need tae wait fur the local indy tae open so's ah can get me bit's that ah need!
Just need tae wait fur the local indy tae open so's ah can get me bit's that ah need!
steve's P38 RR
Active Member
- Posts
- 716
- Location
- Suffolk
Xmas day i fitted my HID headlight convertion and today i washed it, fitted led side lights and 2001 spec rear lights all on my p38.
buckshot
Well-Known Member
- Posts
- 9,841
- Location
- right yer!
got it dirty again on the plain and i did'nt get stuck either! :boink:
:boink:
ratty
I'm not special I'm limited edition
- Posts
- 34,277
I din't do nuffink. I'm waiting for my local indy to open so I can get a drop arm ball joint and wiper arms, blades and spindles.
TheVengefulElephant
Well-Known Member
- Posts
- 6,527
Noticed my NSF tyre was almost flat onto the rim again so pumped er up again!
109party
Well-Known Member
- Posts
- 2,901
- Location
- Funny place of Norfolk
got my donor vehicle running but then found out there is litteraly no clutch well theres a cluth pedal but thats it from what i can see no hoses or anything so engine runs but thats it. does anyone no how you can make a full manual clutch so i can move it easier and wondering why anyone would put electronic ignition wen it starts easily
baggyjim
New Member
- Posts
- 2,063
- Location
- gillingham dorset
fook all again went outside looked at all the ice on the cover sheet and thought nooooo.... went back inside had coffee and looked at winch bumper won on flea bay also put bid on some wheels and tyres maybe tomorrow
also put bid on some wheels and tyres maybe tomorrow
Optimus Prime
Well-Known Member
- Posts
- 5,988
- Location
- Garden of England
washed it, cleaned it inside, made a list of jobs to do
shadowster
Well-Known Member
- Posts
- 1,372
- Location
- 55'38.4n.4'49.1w
adjusted the h/break cable to grt rid of an annoing rattle
flash42
Active Member
- Posts
- 739
- Location
- moretonhampstead, devon
well, me and cousin went ferreting in here this morning and were going to a new burry and thought we could get up this bank in the tractor ruts. well we thought wrong lol
ended up getting very stuck and the onl tools we had was a defender jack, hammer and a tyre iron lol
took us 3 hours to get her out, we were too embarrased to get the farmer out lol
ended up getting very stuck and the onl tools we had was a defender jack, hammer and a tyre iron lol
took us 3 hours to get her out, we were too embarrased to get the farmer out lol
porkflap
New Member
- Posts
- 75
- Location
- derbyshire
rebuild the rear axle with late Rangie classic bits!!
90boy
Well-Known Member
- Posts
- 6,836
- Location
- Worcestershire, Tenbury Wells
pulled a tree down with it and fed the pheasants
buckshot
Well-Known Member
- Posts
- 9,841
- Location
- right yer!
finished off painting the chassis "ish" still some bits the are a pain in the arse to get at (in the middle of the xmember etc )
which will have to wait till the weathers better so i can wash it it out proper ,and both the rear spring out riggers what a bitch to get at (will have to pop the springs out to get it covered).
then when the paint was dry steam cleaned the whole landie (got the other half of salisbury plain out from under it ) has to go in to the stealers in the morning (water and mud getting into the ECU box from underneath) .
cant wait to have a go in the new puma for a couple of days
:cool2:
which will have to wait till the weathers better so i can wash it it out proper ,and both the rear spring out riggers what a bitch to get at (will have to pop the springs out to get it covered).
then when the paint was dry steam cleaned the whole landie (got the other half of salisbury plain out from under it ) has to go in to the stealers in the morning (water and mud getting into the ECU box from underneath) .
cant wait to have a go in the new puma for a couple of days
:cool2:
