thebfg2003
New Member
- Posts
- 28
Fitted new oil seal and bearing on axle. Finally fitted seal on doortop too 
Kev
Kev
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Welding on the new bumper, thats about it really
buckshot
Well-Known Member
- Posts
- 9,841
- Location
- right yer!
chopped off the rear corner over hang and fitted a piece of ali angle to strengthen it
then gave the near side a base coat ready for a little bit of an idea i've got
then gave the near side a base coat ready for a little bit of an idea i've got
- Posts
- 14,902
- Location
- Doncaster
Just come in from work and found me front tyres flat again!
Think I'll have to go to a tyre place to break the beads, clean them and the rims and re-seal them properly. I doubt my compressor would provide enough blow to inflate a tyre from absolutely flat unless it's already sealed ..
Think I'll have to go to a tyre place to break the beads, clean them and the rims and re-seal them properly. I doubt my compressor would provide enough blow to inflate a tyre from absolutely flat unless it's already sealed ..
Barrow Boy
New Member
- Posts
- 31
- Location
- Barrow, Suffolk
I've cut the valence off and put a nice Pro Trac steering guard
Tunelessblues
New Member
- Posts
- 191
Put my sides on and fitted some of the back lights.
wanted to get the roof on but ran out of nuts Damn!
wanted to get the roof on but ran out of nuts Damn!
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Re-fitted the bumper after welding on the bottom panels
That is a mean looking bumper!
ratty
I'm not special I'm limited edition
- Posts
- 34,277
Gave mine a once over before its MOT test tomorow. I was meant to do it on monday but the bits I ordered on sunday via express delivery didn't arrive until 16.15 this afternoon so I couldn't leave the house to go and work on the landy.
There were a few bits that needed doing. I lubed up the O/S/R door catch as it was getting a bit sticky to open, fitted all new track rod ends, adjusted the washer jets, fitted new wiper blades, fitted new number plates front and rear, cleaned the O/S/R brake as it had mud trapped in it and was making a bit of noise.
I still have to re-fit and bolt the battery back in and either change the whole drop arm or replace the drop arm ball joint and I also need to sort out the wiring to the high level brake light all before 9am tomorrow morning.
.There were a few bits that needed doing. I lubed up the O/S/R door catch as it was getting a bit sticky to open, fitted all new track rod ends, adjusted the washer jets, fitted new wiper blades, fitted new number plates front and rear, cleaned the O/S/R brake as it had mud trapped in it and was making a bit of noise.
I still have to re-fit and bolt the battery back in and either change the whole drop arm or replace the drop arm ball joint and I also need to sort out the wiring to the high level brake light all before 9am tomorrow morning.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
danchapman2k2
Well-Known Member
- Posts
- 1,097
- Location
- Writtle, Essex
Had my mud tyres delivered!! Ready to roll soon need a swap over spray my disco1 steels then put them back on! thinking a nice satin black for the disco wheels!! standard landy wheels are JANK! but matt black might suite um
Just had a pop top added by RR concept (www.rrconcept.com) in Lyon in France..anyone else got a land rover camper?
Attachments
Last edited:
waldershelf
Well-Known Member
- Posts
- 2,397
- Location
- In the hills north west of Sheffield
I was in the same position as you I needed to change the ball joint due to a split boot, I bought a tool from Paddocks for about £12, it makes changing the top seat out a doddle. Much easier than doing the whole arm.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
spam
danchapman2k2
Well-Known Member
- Posts
- 1,097
- Location
- Writtle, Essex
Is this lidl porn? Lol
genuinely not spam.. i am a tailor in London and new owner of a defender..Not a garage owner.
did loads of research abt putting on dormobile type roofs and found nothing on UK forums, plenty in Germany and France even a few random Danish companies but all the people I spoke to like Foleys couldnt do a roof that didnt look ridiculous.
did loads of research abt putting on dormobile type roofs and found nothing on UK forums, plenty in Germany and France even a few random Danish companies but all the people I spoke to like Foleys couldnt do a roof that didnt look ridiculous.
