What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
mikescuba
Well-Known Member
- Posts
- 2,731
- Location
- France, Loire, Rhone Alpes
I was tempted to give mine a little pat but the last time I touched it something went wrong.
ratty
I'm not special I'm limited edition
- Posts
- 34,277
I walked past mine twice. I did contemplate doing some work on it but then I decided to go to bed instead.
Big Mat
Well-Known Member
- Posts
- 943
- Location
- King's Lynn, Norfolk
Took it out to pick up some willow, then it wouldn't start :doh: Got it going half an hour later and the i took it home!
- Posts
- 13,779
- Location
- The Principality
The 'tyre place' fitted my winter tyres and wheels on for me today. I had booked it all in advance and had taken the wheels to them a few weeks ago, so it was a very quick job.
Thanks to all the people who offered advice to me a couple of months ago about which tyres to go for - it was acted upon!
Thanks to all the people who offered advice to me a couple of months ago about which tyres to go for - it was acted upon!
finallysnapped
Well-Known Member
- Posts
- 1,127
- Location
- East Lothian
Got my car back from the garage as they were giving a good going over, all new oils and fluids, filters, fan belt, hubs all greased and all that jazz.
Completely surprised at what a massive difference it has made, everything feels so much lighter and more responsive, it must have been long overdue.
Completely surprised at what a massive difference it has made, everything feels so much lighter and more responsive, it must have been long overdue.
andlover
New Member
- Posts
- 265
- Location
- finland (here where santa lives)
got my new mantec snorkel 2 my disco, and new rear sprigs, all tought they were 2cm too short, so i have 2 fabricate plates under rear springs....
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Confused?? how can a set of Landrover springs be 20mm short?? Have you got a lift kit fitted??
crashbox
Well-Known Member
- Posts
- 12,347
- Location
- In the UK, thankfully.
Today I cut off the rear nearside outrigger from my project S3 and welded the new one on. I then cut off the body support bracket, cleaned it up then welded it on to the top of it. Welds all dressed up. Then cut out the rusty bits on the rear nearside of the chassis, ready to weld new metal and box it in like I done on the other side. To ensure the outrigger bracket that supports the rear tub fits correctly, I had fitted a long bit of angle iron, which I bolted to the brackets on either side and spot welded it to the centre supports. Body should fit without too much hassle, I hope.
mud muppet
New Member
- Posts
- 964
- Location
- burton upon trent
put full roof rack on..
and found 4 square spots, so fit them on rack too.
looks the dogs ........
and found 4 square spots, so fit them on rack too.
looks the dogs ........
surreyrock
Active Member
- Posts
- 321
- Location
- Brooklands Surrey
That's the oil cooler pipes done finally... that should stop the oil leaks 
scotchgit
New Member
- Posts
- 2,777
Checked the fluids and pumped up tyres too bloody cold for anything else
joe1972
Well-Known Member
- Posts
- 1,595
- Location
- Manchester
installed a cabin light in the bobtail, and insert decibel insert...still sounds good but much less like a diesel when it's on idle now. Ready to break it at Tong next weekend. Happy days
ratty
I'm not special I'm limited edition
- Posts
- 34,277
Yesterday I used mine for two jobs at work. The first being retreiving a mondeo with a burnt out clutch from down the bottom of a long, steep, slippery driveway, The second was a mercedes which had come off the road and into a ditch.
Today I had to jump in it twice again. The first was a citroen piccasso that had taken a wrong turn down a steel bridlepath, The second was retrieving a stolen 4x4 in a field.
Today I had to jump in it twice again. The first was a citroen piccasso that had taken a wrong turn down a steel bridlepath, The second was retrieving a stolen 4x4 in a field.
- Posts
- 83,255
- Location
- Embasinga stocæ
put £15 worth of doozil in it to go laning - then didnt go and returned Disco to Daftlett .
.
SHORT ROUND
Active Member
- Posts
- 675
- Location
- forest of dean, gloucestershire
is that an original raptor dash as i did'nt see that one when i looked for mine
It's a td5 dash with a Raptor fasia on the console. If you contact Phil Raptor at Raptor engineering he'll prity much make you what ever you want. Mine cost £42.
No spam intended but it is a quality part at a good price.
And looks the dog's nads!!
No spam intended but it is a quality part at a good price.
And looks the dog's nads!!
SHORT ROUND
Active Member
- Posts
- 675
- Location
- forest of dean, gloucestershire
if you look in the things bought for your landy for christmas you'll see the raptor dash i bought and is the most common one i believe.
http://www.landyzone.co.uk/lz/f37/so-what-goodies-buying-your-landie-christmas-170514.html
