ratty
I'm not special I'm limited edition
- Posts
- 34,277
failed in cut on inner sidewall on one tyre. will give me a ticket if I take it back tomoz with "noo" wheels and tyres fitted..............
have "borrowed" some. result!
nice
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
nice
- Posts
- 83,282
- Location
- Embasinga stocæ
then i can get on with refurbing the rear prop and changing the rear brake pads......................
1 is down to 1mm!!!!
1 is down to 1mm!!!!
ratty
I'm not special I'm limited edition
- Posts
- 34,277
:doh::doh::doh:
- Posts
- 83,282
- Location
- Embasinga stocæ
hey - 1mm is better than some ive seen
ratty
I'm not special I'm limited edition
- Posts
- 34,277
Co-Pang-Yang
Well-Known Member
- Posts
- 2,930
- Location
- Colchester, Essex
Picked up some new pistons and seals for my caliper, took it apart bar one piston that would not budge.
Took the old seals out, tried putting in new seals and metal rings. Knackered two rings before i gave up and put the old stuff back in to get me home. Gonna pick up another set of seals tomorrow and try again.
Took the old seals out, tried putting in new seals and metal rings. Knackered two rings before i gave up and put the old stuff back in to get me home. Gonna pick up another set of seals tomorrow and try again.
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
what are you using to get them out? i like to use compressed air and clamp the other pistons in
Co-Pang-Yang
Well-Known Member
- Posts
- 2,930
- Location
- Colchester, Essex
Well armed with a new seal kit yesterday i had another go and i'm happy to report i succeeded! Popped new pistons in (longer as RST gave me the wrong ones) re-fitted the caliper and bled the system and all seems well.
I did use the air line to pressurise the caliper and push the pistons out. Got 3 out with this method, however the last one still wouldn't budge.
Ended up putting a thin piece of wood in the gap of the caliper that allowed all the pistons to move out about 3/4 of the way.
Then as i was replacing the pistons any way i put the caliper in a vice clamped the last problem piston with the mole grips and hit them with a hammer till it pulled it free. :lol:
Crude but effective.
Chris.
I did use the air line to pressurise the caliper and push the pistons out. Got 3 out with this method, however the last one still wouldn't budge.
Ended up putting a thin piece of wood in the gap of the caliper that allowed all the pistons to move out about 3/4 of the way.
Then as i was replacing the pistons any way i put the caliper in a vice clamped the last problem piston with the mole grips and hit them with a hammer till it pulled it free. :lol:
Crude but effective.
Chris.
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
i stuck the callipers on the rear axle and put nice new copper/nickel brake pipes on also dug out my old spare wheel with no tyre on to get it shot blasted
- Posts
- 83,282
- Location
- Embasinga stocæ
stripped and rebuilt with stainless pistons one disco rear caliper
farmershort
Well-Known Member
- Posts
- 1,067
- Location
- West Berkshire
changed front n/s wheel bearings last night....
tonight - trying to renew the front radius arm bushes - and failing
tonight - trying to renew the front radius arm bushes - and failing
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
where did yer get the kit from?
- Posts
- 83,282
- Location
- Embasinga stocæ
Keith Gotts
Stainless steel Piston - ref #606696ST @ £7 each.
Seal kit - ref #aeu1546 @ £9.02. ****
**** the seal kit supplied is suitable for one 2 or 4 pot caliper, so 1 kit will do two 2 pot calipers
.
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
ah so i would need 3 kits....... and 10 pistons ........doh!
- Posts
- 83,282
- Location
- Embasinga stocæ
why - yu got 5 disk brakes on yo motor?
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
your right...... i need 12
- Posts
- 83,282
- Location
- Embasinga stocæ
? 3 pot calipers?
GRATCH
HUGE MEMBER
- Posts
- 15,475
- Location
- North Cheshire
- Posts
- 83,282
- Location
- Embasinga stocæ
that makes more sense
Co-Pang-Yang
Well-Known Member
- Posts
- 2,930
- Location
- Colchester, Essex
Drove through a conifer on my mates farm by accident.
Now need a new flexi ariel. Current one was only 2 weeks old.
Now need a new flexi ariel. Current one was only 2 weeks old.
