What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
i gotta do mine at some point.... i'm thinking a dirty gert hammer and beat it out
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
what one have you fitted adjustable?
one I removed was adjustable, full of **** and totally ****ed.
think it's a Bearmach or all makes one.
Not adjustable
Last edited:
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
so its a lockheed one you fitted?
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
most likely all makes or summat they like plastic packs
trax99
Well-Known Member
- Posts
- 1,149
- Location
- Montgomeryshire
changed the passenger window regulator - then banged me shin on the tow hitch
bastard
bastard
bastard
bloody great lump on me shin now, I dont think my disco likes me, every time I work on it I bang, cut or graze some part of me anatomy
bastard
bastard
bastard
bloody great lump on me shin now, I dont think my disco likes me, every time I work on it I bang, cut or graze some part of me anatomy
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
today i removed all the wiring from the bulkhead with a pair of side cutters 
my little bro removed the vac tank from the inner wing, and i found that even when a chassis has been stored in a dry garage most of its life the bolts that hold the rear lashing eyes on will still be seized and refuse to come out currently being soaked in wd40 in the hope they will come out tomorrow
my little bro removed the vac tank from the inner wing, and i found that even when a chassis has been stored in a dry garage most of its life the bolts that hold the rear lashing eyes on will still be seized and refuse to come out
currently being soaked in wd40 in the hope they will come out tomorrow
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
hope you didn't get a britpart one, i did one for a customer using a britpart one and it dropped the window when the welds snapped
Sirus
Your all Banned except me
- Posts
- 22,196
- Location
- The Country of Black
Sunday fitted new set of swivell bearings and seal on me 110. Hopefully the clunking will have stopped now.
Today I fitted new trackrods and ends and welded up me outrigger. Then stripped me steering guard for a repaint. Gave me bumper a rub down and a coat of red oxide as it was looking in a sorry state after its trip through the spanish salt mines. Going out now to give it a sand and a coat of shiny black. MOT is due and tax is up the end of the month so best get it done soon.
Today I fitted new trackrods and ends and welded up me outrigger. Then stripped me steering guard for a repaint. Gave me bumper a rub down and a coat of red oxide as it was looking in a sorry state after its trip through the spanish salt mines. Going out now to give it a sand and a coat of shiny black. MOT is due and tax is up the end of the month so best get it done soon.
nathan5346
Well-Known Member
- Posts
- 11,939
- Location
- oldbury
I used a Jerry Can aswell cos i didnt wanna waste any of that tenner driving back from the petrol station!
Sirus
Your all Banned except me
- Posts
- 22,196
- Location
- The Country of Black
Have painted me bumper and seam sealed the footwell on the series 2
landy10
New Member
- Posts
- 1,872
picked the landy up from its mot, needed a number plate light bulb a foglight bulb a hazard warning switch and a front wheel bearing. not bad for a 20 year old landy that aint turned a wheel in a year and a half. Do a service when i got time, tidy it up a bit then sell it
foss
New Member
- Posts
- 1,734
- Location
- The muddiest driveway in Essex
picked up chassis & diff...oooh its excitin!
Similar threads
Discovery Sport
Need some advice please