Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Hub seal has gone. what you can see is diff oil (EP80/90)
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
the rumbling could be the ujs on the propshaft or wheels bearings etc
I'd go with wheel bearing is shot LAND ROVER DEFENDER, DISCOVERY 1, RANGE ROVER WHEEL BEARING KIT - STC4382 | eBay something like this will sort that out and due to the bearing being shot it is causing the noise and has worn the seal holding your diff oil in the axle casing. simple job if your handy on the spanners just make sure everything is clean as it goes back together
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
Go for timken ones by far the best.
- Posts
- 7,920
- Location
- East Midlands
Plenty of nice new grease too.
cornish rattler
Well-Known Member
- Posts
- 6,432
- Location
- Manc chester
cornish rattler
Well-Known Member
- Posts
- 6,432
- Location
- Manc chester
Fitted an RDX steering wheel 
easye1
Banned
- Posts
- 8,557
done a vary rare landy thing today,
I topped up the engine oil...
put 1 litre in but was a little over full at cold standing..
dont seem to use engine oil bless it.
did take it for a run round the shops, leaving it ticking over while grandaughter inside the shops, with my rad now half covered with last years double walled plastic sheet I cut for it, it helps in warming that old engine up....
stops the cold air blasting the drivers side also...
I topped up the engine oil...
put 1 litre in but was a little over full at cold standing..
dont seem to use engine oil bless it.
did take it for a run round the shops, leaving it ticking over while grandaughter inside the shops, with my rad now half covered with last years double walled plastic sheet I cut for it, it helps in warming that old engine up....
stops the cold air blasting the drivers side also...
v8geoff
Well-Known Member
- Posts
- 3,327
- Location
- chippenham,wiltshire
nothing better than getting your landie back after you ant had it for a while great news
has the pump been tweeked to far so it's over fueling somehow?
filled mine up and straightened out the rear corner after meeting the container loading ramp at work really need to get some work lights as reverse lights so I can see where I'm reversing properly
filled mine up and straightened out the rear corner after meeting the container loading ramp at work
really need to get some work lights as reverse lights so I can see where I'm reversing properly
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
got a pair of LED work lamps for the 110
has the pump been tweeked to far so it's over fueling somehow?
filled mine up and straightened out the rear corner after meeting the container loading ramp at work
Update found a loose head bolt no more smoke but heater doesn't HEAT .
Strange as I followed Haynes bible
skint-as-usual
Not a well Known Member - with no likes
- Posts
- 2,411
- Location
- County Durham
Done nothing.
But got through MOT only 1 advisory.
Success.
:cheer2:
But got through MOT only 1 advisory.
Success.
:cheer2:
Think mine is dying got white/blue smoke on start up until it's warm. Oil leaking all over the top of the cam belt housing, bubbling up between the housing and the block. Noticed my oil light flickering slightly on idle earlier as well. Got a new (second hand) head for it but everything seems to be going wrong.
got white/blue smoke on start up until it's warm. Oil leaking all over the top of the cam belt housing, bubbling up between the housing and the block. Noticed my oil light flickering slightly on idle earlier as well. Got a new (second hand) head for it but everything seems to be going wrong.Similar threads
Discovery Sport
Need some advice please