What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
mephitic
Active Member
- Posts
- 174
- Location
- Abruzzo, Italy
Replaced the brake master cylinder on the 200tdi Disco, because it was ****ing fluid everywhere, then tightened up the adjustment screw a tad on the well past its best steering box.
The 300 Disco had its leaky output shaft seal replaced, along with new hand brake shoes, springs & a cable, so that's another leak (hopefully) sorted out.
The 300 Disco had its leaky output shaft seal replaced, along with new hand brake shoes, springs & a cable, so that's another leak (hopefully) sorted out.
- Posts
- 7,877
- Location
- East Midlands
I've been getting an error code occasionally, namely 15.2 high speed crank (logged). Recently, it's been showing up more often. Reading on here and elsewhere suggests that this often has something to do with a poor signal from the crank position sensor. I tried shimming it out with a washer, and the car wouldn't start at all. Then I swapped it for a spare one that I'd taken off in January and the engine started. I've taken it for a run with some opportunities for a long blast where I can get up to 70, and the error hasn't returned, so maybe that's what it was.
- Posts
- 83,273
- Location
- Embasinga stocæ
seam sealed welded panels, derusted and kurusted other sill and floor.
sprayed with hammerite, will underseal it all tomoz if dry else next w/e/
sprayed with hammerite, will underseal it all tomoz if dry else next w/e/
Carried on tinkering, thought I'd check glowplugs ready for winter (I know the 300 tdi shouldn't need them but they are there so may as well check), got power to No1 cylinder so that meant all plugs getting power as No1 is at the far end of the power lead. Disconnected all plugs and continuity checked them to ground, No1 & 2 fine 3 & 4 duff, all 4 changed - job done!
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
Ninety gave up its 2.5 n/a Engine today
Both gearboxes out and Disco steering box fitted
Looking good Pete looking good.
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
Yeeeaaahhh who cares what people think as long as you like it mate......Shall I spray the 200tdi blue all over before it goes in ?
If I get a nice day in the week I'll spray it up except for the inlet manifold, could buff that up shiney for some bling
800 miles after I fit the refurbished 200tdi in my Defender, I checked most bolts/screws/jubilee clips just to see if they were all still tight, has leaked hardly any oil which is nice, fitted another fuse box, so now have one for the main and aux battery. Sorted the air horn which was down to a ruined relay bloody Italian ****e. Also wanted to clean it but ran out of saturday Should hopefully get a chance tomorrow
bloody Italian ****e. Also wanted to clean it but ran out of saturday Should hopefully get a chance tomorrow 
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
driven it on a 350mile round trip to Spalding Lincs. To collect a new (well newer) pikey wagon.
- Posts
- 83,273
- Location
- Embasinga stocæ
wotcha doing with the old one?
blue beasty
Leaks an prone to bits dropping off
- Posts
- 63,035
- Location
- Gloucestercotshirewolds
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
It's gonna be used as a den of inequitity Ermm I mean 110Woman is having it..
:behindsofa:
- Posts
- 83,273
- Location
- Embasinga stocæ
k
Discovery2TD5
Active Member
- Posts
- 458
- Location
- West Yorkshire
Changed a flat and took the old one to be repaired.
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
timberjock
Active Member
- Posts
- 366
had new brake servo fitted, now it actually stops when it should
