What have you done to your Landie today.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Wirenut said:
Wen I hit your name it just gives me general info .. I see you joined the group in 7/24/09 :) 7/24/69 is my BDay ! Well I'm getting in my disco now to start working on it a bit I'm not sure where I'm going to start yet cuz I yet .. I first have to get some wd40 we are custommizing my hitch for some hauling bikes and stuff for the trails :) :)
Click to expand...

no i joined in july 08.well good luck with whatever you do to it.you know where i am if needed.;):D
 
gemsdad said:
no i joined in july 08.well good luck with whatever you do to it.you know where i am if needed.;):D
Click to expand...

O my bad 08 but it is still July 24th my BDay .. This is my eng and what you could see the type of stuff I have in there :) under hood ..
y6a7yhub.jpg
 
Just ordered some Track rod ends. Thought I would go for more up market ones as the last ones that came in a blue box only lasted four years. Ordered a new down exhaust pipe, rear brake shoes, rear wheel cylinders, Brake adjusters and a steering damper.
New foot wells get fitted next week. I will then give it a grease up and I should be ready for the winter. Normally when I feel good about my Defender and spend some money on it, something else goes.
 
My landy is off the road at the moment. The clutch slave cylinder went. Had it towed back and the recovery worker noted that the handbrake didnt work too well. How do I adjust the cable. It has had new shoes within the past year
 
Set about finding the source of the intermittent squealing noise & stench of burning rubber on the 300tdi. Since my missus was mad keen to get her motor back she came to help. It turns out that the bottom ac pulley bearing was utterly fubar, a tad surprising as it was only replaced a couple of months ago. Could have been much worse, so bit of a result really.

IMG00101-20131109-1015_zps829d4155.jpg
 
I popped over to see LZ's resident porn connoisseur. We fitted a new stub axle and wheel bearings to his slitty powered 90.

Travelling over to him I freed off my turbo wastegate as it was sticking yet again.
 
Fitted new rear springs shocks and trailing arm bushes to the 110, Was going to do the fronts but weather stopped play :mad: So that's tomorrows job.
 
bigvinnie said:
Using this , mate material . Should of said its flexable enough but its a pain to fit round the contours, so its ended up wrinkly...should of paid some one else tae do it. balls....you would of thought that had yu seen ma pressie wrapping!:rolleyes:
Click to expand...

Haha not the easiest thing to do I carpeted mine but bet it was the top rear left and right that where the hardest to do.
 
benjy8 said:
My landy is off the road at the moment. The clutch slave cylinder went. Had it towed back and the recovery worker noted that the handbrake didnt work too well. How do I adjust the cable. It has had new shoes within the past year
Click to expand...

My crystal ball tells me you have a 1999 Freelander 1.8 (PETROL), alas it don't tell me how to sort it, but someone will be along shortly...

by the way, don't forget to intro yerself proper like :D
 
bigvinnie said:
mines a 110 csw mate wea sunroof, so every bloody panel has snapped me!...easiest part was the rear trim above the door:rolleyes:.....it I,ll do better than it was but think i'll look fur a local service!
Click to expand...

Rrrr rite you have got a lot to do then good luck pal take your time and try not to swear at it and it'll look rite.
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
527
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
604
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
883
Knappster
Knappster
Mooky
Replacing thermostat
Replies
12
Views
417
miktdish
miktdish
I
Re-coding of ABS Module after repacement
Replies
10
Views
962
invisible999
I
Back
Top