kernowsvenski
Well-Known Member
- Posts
- 1,617
- Location
- Truro
That is the answer I should think.
What have you done to your Freelander today
- Thread starter Freelaner
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
That is the answer I should think.
Pluribus
Active Member
- Posts
- 247
- Location
- Sevenoaks, Kent
Bounty
Well-Known Member
- Posts
- 255
- Location
- Cheshire, United Kingdom
Rammed a tack through the rear tyre
Neither intentionally nor with any effort but it's there now and whoever pulls it free will be crowned king of England
Neither intentionally nor with any effort but it's there now and whoever pulls it free will be crowned king of England
Jayridium
Well-Known Member
- Posts
- 1,416
- Location
- Pedronapper (Peterhead)
Are you really going to nominate a tyre fitter King of England?
Jayridium
Well-Known Member
- Posts
- 1,416
- Location
- Pedronapper (Peterhead)
Bounty
Well-Known Member
- Posts
- 255
- Location
- Cheshire, United Kingdom
Fumin
Replaced that with the spare... also pulled apart most of the boot, subwoofer lid is detached, carpet retainers unscrewed but seems the carpet is now trapped under the sides which I haven't yet figured out how to release
After I got the temperature sensor mod I'm sure some would think so!
Replaced that with the spare... also pulled apart most of the boot, subwoofer lid is detached, carpet retainers unscrewed but seems the carpet is now trapped under the sides which I haven't yet figured out how to release
After I got the temperature sensor mod I'm sure some would think so!
Last edited:
Release the 4 hooks by turning anti clockwise. Pull the rear door seal away from the side panels. If it's a 5 door, then remove the luggage cover and remove the screw from the cover bracket. Move the back seats forward and remove the clasp hoops. I think the seat belt lower bolt needs removing too. The side panel will then pop off it's retaining pins, if it's given a tug.
Bounty
Well-Known Member
- Posts
- 255
- Location
- Cheshire, United Kingdom
If it's a 5 door, then remove the luggage cover and remove the screw from the cover bracket. I think the seat belt lower bolt needs removing too. The side panel will then pop off it's retaining pins, if it's given a tug.
I'd have never found those screws! So close.. well, the lower seatbelt bolt should come off to remove the panel but I only needed the carpet, releasing it from the loadspace loops and some good pulls got it free from underneath. Semi sunny day so it should dry now. Kind of like the bare metal look in the back, but alas...
No sign of the water ingress, but at least it's dry now
andyfreelandy
Well-Known Member
- Posts
- 5,563
- Location
- Devon
Sold one of the fleet. TD4 manual. Gone oversea to Wales. Well, he drove it round the roads to get there!!
Found out my TD4 auto needs an Mot. Really crept up on me this year!! Plan is to refurb and make beautiful underneath, but not enough time as it is due Monday!
So, another experiment, cleaned brake pipes back to shiny metal and painted with cold galvanising paint. See if that can hold back the Devon damp and rust!
Also, found another sticking disc slider. Another one with rubber on had stuck, so replaced with plain sliders.
Stripped and rebuilt rear brakes and handbrake now on the button.
Let's see what else they find wrong!!
Found out my TD4 auto needs an Mot. Really crept up on me this year!! Plan is to refurb and make beautiful underneath, but not enough time as it is due Monday!
So, another experiment, cleaned brake pipes back to shiny metal and painted with cold galvanising paint. See if that can hold back the Devon damp and rust!
Also, found another sticking disc slider. Another one with rubber on had stuck, so replaced with plain sliders.
Stripped and rebuilt rear brakes and handbrake now on the button.
Let's see what else they find wrong!!
Bounty
Well-Known Member
- Posts
- 255
- Location
- Cheshire, United Kingdom
Sprayed the underside, found the leak around the edges of the recess, popping underneath in a min to rescue the 10 plastic pins before they get melted during welding. Now that the thing is completely disassembled I'm going to scrub off the plastic too with some kitchen brillo wire
NeilTD4
Active Member
- Posts
- 385
- Location
- Warwickshire
Changed the power steering fluid reservoir. From what I've read, not a bad idea on a 10 year old FL2. Will gradually replace the fluid over the coming weeks...
Pluribus
Active Member
- Posts
- 247
- Location
- Sevenoaks, Kent
Gave her a courtesy wash inside and out as she's going to the garage tomorrow to have the cat welded back together...
- Posts
- 380
- Location
- Cheshire
The mrs managed to leave it running for two hours on the drive after it somehow locked itself!
RAC came out and sorted it
RAC came out and sorted it
GrumpyGel
Well-Known Member
- Posts
- 26,393
- Location
- Christchurch, New Zealand
I've had to rescue Mrs Grumpy after she has managed to lock herself out of the car with it running before. Not the Freelander though.
- Posts
- 380
- Location
- Cheshire
I have ordered the same kit off flea bay that the RAC used to open it!
GrumpyGel
Well-Known Member
- Posts
- 26,393
- Location
- Christchurch, New Zealand
Pluribus
Active Member
- Posts
- 247
- Location
- Sevenoaks, Kent
Just discovered the glovebox has a light in it, so reconnected the cables to the terminals, and hey presto, a 2.5" illuminated box!
Now if only I knew what was wrong with the hazard switch led... Originally I didn't think it lit up, as it never did in 9 years of driving her, but then, completely randomly on the motorway one night, there she was, lit up in all her glory. Worked great for a couple of weeks, then back to no light as she was before...
Now if only I knew what was wrong with the hazard switch led... Originally I didn't think it lit up, as it never did in 9 years of driving her, but then, completely randomly on the motorway one night, there she was, lit up in all her glory. Worked great for a couple of weeks, then back to no light as she was before...
andyfreelandy
Well-Known Member
- Posts
- 5,563
- Location
- Devon
My 171k miles TD4 failed its Mot on 3 things.
Tiny hole in rubber boot on track rod end, fair enough. Fitted new rod end.
Anti roll bar moved to one side, fair enough, now fitted new clamp rings and new bushes.
However, it failed on the rear VCU bearing as having 'play' in it. There is no play in it, just gone to all the work of changing the bearing and there really is nothing wrong with it. Slight cracks in the rubber but certainly no play.
Guess it wasn't my hippo's day!
All sorted and back for free retest.
Tiny hole in rubber boot on track rod end, fair enough. Fitted new rod end.
Anti roll bar moved to one side, fair enough, now fitted new clamp rings and new bushes.
However, it failed on the rear VCU bearing as having 'play' in it. There is no play in it, just gone to all the work of changing the bearing and there really is nothing wrong with it. Slight cracks in the rubber but certainly no play.
Guess it wasn't my hippo's day!
All sorted and back for free retest.
Similar threads
