B34R
Active Member
- Posts
- 410
Nupe, just soaked the old ones in brake cleaner till they came up good! The trick is not levering them in odd ways while trying to remove em!
What have you done to your Freelander today
- Thread starter Freelaner
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Alibro
Well-Known Member
- Posts
- 7,171
- Location
- Northern Ireland
I was worried mine might break or be badly corroded so bought new before even taking the hubs off. I probably could have got away with the originals but for the sake of £11 I thought it wasn't worth it.
Tempus Fugit
Well-Known Member
- Posts
- 17,580
- Location
- Great Britain
Cracked the windscreen. Replacement being fitted on Thursday.
Didn't half go with a bang, nothing showed initially, then a split appeared and extended.
Didn't half go with a bang, nothing showed initially, then a split appeared and extended.
stannswhite
Well-Known Member
- Posts
- 622
- Location
- leeds
nowt its still offroad,i mean broken.
.
.
tonytherunner
Active Member
- Posts
- 339
- Location
- wherever the road takes me
Not today but i made a custom battery clamp ..cnc cutting....stainless steel
Alibro
Well-Known Member
- Posts
- 7,171
- Location
- Northern Ireland
MOT'd it
Fitted new brake shoes and track rod ends last week then on Sat I checked lights etc then power washed underside and cleaned outside and in and she flew through.
Now just have to figure out why the header tank was empty.
Fitted new brake shoes and track rod ends last week then on Sat I checked lights etc then power washed underside and cleaned outside and in and she flew through.
Now just have to figure out why the header tank was empty.
htr
Well-Known Member
- Posts
- 1,555
- Location
- Central Otago, Southern New Zealand
Ordered a set of replacement Dobinson springs today. Sorted out a 'spare' set of rims to put mud tyres on. The are tidier that what's on my FL!
Island 4x4 must use a slow boat to deliver their parts - ordered on the 12th not here yet [ lower tie bar, heater hose and an oil filter]
Island 4x4 must use a slow boat to deliver their parts - ordered on the 12th not here yet [ lower tie bar, heater hose and an oil filter]
htr
Well-Known Member
- Posts
- 1,555
- Location
- Central Otago, Southern New Zealand
I'm expecting a bit of a lift above original [new] height of about 20mm.
slimboy
Active Member
- Posts
- 207
- Location
- Fareham Hampshire
New center section and back box fitted £165
stannswhite
Well-Known Member
- Posts
- 622
- Location
- leeds
ive got my FL back from repair & its good to go,
cost an arm n a leg though..
cost an arm n a leg though.
.
htr
Well-Known Member
- Posts
- 1,555
- Location
- Central Otago, Southern New Zealand
Removed alloy sump guard to straighten it and replaced the lower engine tie bar.
stannswhite
Well-Known Member
- Posts
- 622
- Location
- leeds
after new alternator put on,gave it a good run today
it sounds pretty good after being laid up a few weeks..
it sounds pretty good after being laid up a few weeks.
.
GrumpyGel
Well-Known Member
- Posts
- 26,355
- Location
- Christchurch, New Zealand
Replaced brake disks this evening. Never changed disks before so was surprised how easy the job is. The longest part was cleaning up the new disks. They were new genuine LR from a main dealer - but have obviously been sitting in a corner of their parts warehouse for a long time. There wasn't a spec of rust on them , but waxy coating took quite a bit of elbow grease and meths to clean up. Still I'm not complaining, $50 (£20) for a pair of disks from a stealer is a bit of a result.
One of the pistons took quite a bit of persuasion to retract enough to slide the caliper & pads off the old disk (lip around the edge and reason for replacing). Probably means it will need some TLC soon.
One of the pistons took quite a bit of persuasion to retract enough to slide the caliper & pads off the old disk (lip around the edge and reason for replacing). Probably means it will need some TLC soon.
Similar threads
