What have you done on your 90/110/130 today?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Scaley Back said:
I've discovered the cause of my Gremlins with my lights.

Looks like I need to replace the Glass Fuse Holders with some Blade Fuse Holders

Only issue is that I don't have the ratings sheet on the back of the fuse panel cover. Instead I have some white sticky labels and the writing is that faded I can't make it out. I seem to have a lot of 25A fuses and I'm guessing they might be a bit higher than what should be there.

If anyone has a Pic of what they should be or can point me in the direction of where to find the info, that'd be great. It's a 1989 90 2.5TDI

Cheers
Click to expand...

This is what mine says...

20220915_100529.jpg
 
M took the fender for its MOT to day, Tester asked why M wanted a 26yr old tractor (he remembered her from yesterday with the L322) then proceeded to ask if it was for sale, errr NO:rolleyes:. We usually get a couple of offers to buy every year.
He said its solid and passed with flying colours:D.

J
 
Finally managed to fit LED lights into the dash last night (after struggling with my wife’s tweezers to get the speedo bulbs in). Lots of swearing, but looks good.

I’m regretting adding an LED bulb to the interior light. It’s just too white/bright compared to the original orange/warm glow. I’ll probably change that back.

Today’s job has been taken off and applying primer to one of the door cards. Queue lots of huffing when I couldn’t get the clip off of window winder mechanism!

Aiming to start respraying tomorrow.
 
GRATCH said:
Probably going to be bolted to the engine.
I've not decided where I'm putting it yet, nor how it will actually mount. There is nothing there to cable tie it to.
Click to expand...
On the inner wing is a good place, just need to make sure your pipe fits.
If you bolt to engine you need another bracket.
(You also need 4 of the rubber cotton reels to stop vibrations)
 
Hicap phill said:
On the inner wing is a good place, just need to make sure your pipe fits.
If you bolt to engine you need another bracket.
(You also need 4 of the rubber cotton reels to stop vibrations)
Click to expand...
Where ever I bolt it, I'll still need another strap.;)
A flat plate bolted to the air-con compressor mount points on the Disco engine would be easy.
I do have new rubber damper mounts.
 
GRATCH said:
Where ever I bolt it, I'll still need another strap.;)
A flat plate bolted to the air-con compressor mount points on the Disco engine would be easy.
I do have new rubber damper mounts.
Click to expand...
Just looked through spares…. Nothing…
Now I know I had 1 of them brackets(onto the engine) somewhere but the shed is a bomb site at the moment.
Unsure where they bolt to,going by the attached looks like head bolts?
B06B1887-8859-4B98-9801-E4ACF1EF3F11.jpeg
 
nothing for a while as busy in work but hopefully today I'll sort the non-working rear lights (probably fuse related? I have more moddern 'blade' fuseholders to replace the glass torpedo things) and maybe it's ready for mot?

Rich.
 
okey, sorted the rear lights - was a bad fuse in fuseholder connection :rolleyes:
then drivers headlight / dip was out....
then drivers headlight / dip was working:confused:

Lucas wiring?????

:eek:

didn't have time to swap fuseboxes BUT they're on my list:cool:

Rich.
 
Mrs has been out in it. Started up ok,wipers worked & horn worked.

I drove it later no horn again.. oh well
Mrs is out again tommorow in it. I keep saying the S1 needs to go for a run out.
 
Drove the 90 to the Newbury sale. It had a decent run, around 110 mile round trip. A sidelight bulb has failed and I topped up the brake fluid. I bought a couple of the rubber clamps to hold tools in the back of the 90. I won’t type the name of these clamps as it sounds dodgy and a mis-type in google could cause some issues… :eek:o_O
 
You must log in or register to reply here.

Similar threads

DefendingLancashire
300TDI Four-parter: brake wear, lift pump / fuel filter, turbo, and bushes / squeaking
Replies
13
Views
493
miktdish
miktdish
F
What have you done with your series today?
Replies
4
Views
1K
Frustrated Seriesist
F
Blob
L322 Let's have your technical opinions then. Coolant leak and cracked manifold?
2
Replies
24
Views
4K
Blob
Blob
Hippo
What have you done to your tratter today?
2 3 4
Replies
70
Views
7K
IamRobbie
IamRobbie
Hippo
What have you done to your tratter today?
2
Replies
35
Views
4K
dominicbeesley
dominicbeesley
Back
Top