What did you do with your Range Rover today

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Never really noticed, but it's the torque converter on the 8 speed only used while stationary?
It's occurred to me I've never seen the revs'flare' as you would with an old fashioned auto box
Ie driving along at say 30 mph.. accelerate it decelerate and the revs match speed, like a manual box.
Is that how it's supposed to be?
Like the p38 has a torque converter lockup on 3rd and 4th the later ones it's lockup is on every gear. If you like.. ;)
 
Never really noticed, but it's the torque converter on the 8 speed only used while stationary?
It's occurred to me I've never seen the revs'flare' as you would with an old fashioned auto box
Ie driving along at say 30 mph.. accelerate it decelerate and the revs match speed, like a manual box.
Is that how it's supposed to be?

Gearbox software has improved a lot over the years and so have the mechanicals, although they look so complex now you need to be a gearbox guru to understand it all. Plus, the TDV8 has so much insane torque the engine barely notices the load.
 
Thinking i need to do an oil change sooner than later.. if it's a diy job on the drive..

Looks DIYable on the drive to me. Look out for the special LR tools required though:rolleyes:, also the need to discard this and that? maybe they are plastic plugs, or they don't trust LR mech these days to change an O ring:D

Temp seems important, but doesn't seem to need engine running for final level check.
Make sure you use the right oil, It wont be cheap:eek:.

J
 

Attachments

  • gearbox oil change.pdf
    320 KB · Views: 119
  • gearbox level check.pdf
    418.1 KB · Views: 93
Was having a play with the nanocom and there was a code for the purge valve circuit open so had a look under the bonnet and sure enough found it was unplugged, plugged it back in cleared the code and it stayed off.

In the short bit of use it seems to run smoother I would say. Only had a small drive though not been able to open up the taps so to speak.

Seems to have mostly sorted the smoking too. I reckon it must have been overfueling with it disconnected as rave seems to states that it could affect the fuel map like that if the valve itself was stuck.

Might explain that strong fuel smell I was talking about a while back too. Though that had pretty much eased off after about a week in fairness
 
Fixed the rear washer - eventually extracted the sprayer from the tailgate, the nozzle came out of the tube much easier. Flow was excellent without that in so used a dental tool to pop the ball out and thoroughly clean the fittings. Loads of crud trapped. All back together and working perfectly.
Checked the auto box level while jacking him to extended, so I could then do a patch on the worst blow on the middle box. Nice wad of foil and gun gum laminate (8 layers I think) under the wrap to try to keep the noise level down while waiting for the new exhaust parts.
Couldn't find anything major with the cruise control - certainly not finding any leaks across to the dump on the brake pedal. But there were some slight cracks and looseness on the hose at one joint so I have taped over it solidly to see if it makes a difference. Time will tell.
 
I finally completed the top-side works for my little refresh project on my 1999 4l V8 p38. Car has been off the road for a couple of years and don't have any history on it past 2015. I replaced rocker cover seals and sealed off where an LPG system was fitted. In the process I also replaced:
  • Inlet gaskets except for valley gasket
  • Plugs
  • HT leads
  • Injector o-rings
  • Aux drive belt
  • Left washer jet on bonnet
Today I tightened up the last bits and prepared engine for the next steps. Next I'll fill it up with coolant, let it run with an engine flush and drain the oil. Then I'll tackle the sump gasket.
 
Was having a play with the nanocom and there was a code for the purge valve circuit open so had a look under the bonnet and sure enough found it was unplugged, plugged it back in cleared the code and it stayed off.

In the short bit of use it seems to run smoother I would say. Only had a small drive though not been able to open up the taps so to speak.

Seems to have mostly sorted the smoking too. I reckon it must have been overfueling with it disconnected as rave seems to states that it could affect the fuel map like that if the valve itself was stuck.

Might explain that strong fuel smell I was talking about a while back too. Though that had pretty much eased off after about a week in fairness

PO has clearly been tinkering.

There's a canister that collects vapour from the tank and then opens during running and burns it. I assume there's a vent to air should it fail which is probably what you were smelling.
 
PO has clearly been tinkering.

There's a canister that collects vapour from the tank and then opens during running and burns it. I assume there's a vent to air should it fail which is probably what you were smelling.
Yes very likely! I wouldn't have left that disconnected though, at least not intentionally
 
Thinking of checking the autobox level today.

Am I correct in thinking, it should be done with the engine running and moving it through the gears, I assume both high and low range? Then crack off the filler plug and if its at the right level it should flow out? I assume you keep it running while checking too so its not running it through the gears and then engine off and then check.
 
Back
Top