RangeRoller dt
Well-Sprung Member
- Posts
- 14,393
- Location
- Trapped inside my head @ LZ asylum
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
RangeRoller dt
Well-Sprung Member
- Posts
- 14,393
- Location
- Trapped inside my head @ LZ asylum
You’ll never guess his name 
give you a clue it’s not Fido
give you a clue it’s not Fido
Rex? All dogs are named Rex, with the exception of every dog I know!
Quick question so, is it a difficult job to change the cam shaft, push rods and followers and timing gear at a 3.5 l V8? Not sure my mechanic contact works out, which would leave me with JLR. Not that I have a problem with their prices, they chaege all of 10 bucks more per hour than the small independent ships around here, but they managed to do some pretty stupid mistakes last time. If the camshaft change and so on is easy enough, I might be tempted to do it myself...
Quick question so, is it a difficult job to change the cam shaft, push rods and followers and timing gear at a 3.5 l V8? Not sure my mechanic contact works out, which would leave me with JLR. Not that I have a problem with their prices, they chaege all of 10 bucks more per hour than the small independent ships around here, but they managed to do some pretty stupid mistakes last time. If the camshaft change and so on is easy enough, I might be tempted to do it myself...
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Dobbin?Funny name for a dog Jack.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Dobbin?You’ll never guess his name
give you a clue it’s not Fido
Didn't do anything on the car, but another project is, more or less, finished:
A quick check of the maintenance invoices unearthed something interessting so, a compression check from 2013, or 20,000 km ago. All cylinders were between 10 and 11 bar! I learn something new about her every day!
A quick check of the maintenance invoices unearthed something interessting so, a compression check from 2013, or 20,000 km ago. All cylinders were between 10 and 11 bar! I learn something new about her every day!
- Posts
- 2,427
- Location
- Isle Sheppy
That’s a big cheese knife
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Short answer is no.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
You'll be surprised how easy a job it is and wonder how garages charge so much.
and the dogs name is Mary.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,393
- Location
- Trapped inside my head @ LZ asylum
I get I am getting on a bit and my eyes are rubbish, but are you trying to show something in the picture? Is dark as ****.
Not sure what you think an easy job is, but if I understabd the workshop manual correctly, almost the complete engine needs to bi dismantled... The easiest part seems to be the top end to replace followers and push rods...
Ok, just had a look at things. The top isn't too difficult it seems. After all I already had the rocker covers and carbs of, which leaves thebinlet manifold and eight (?) bolts for the rocker shafts. That's doable. Leaves the front. I already had the grill and stuff of for the inner wings, so just draining the coolant and disconnecting a hand full of hoses, easy enough. Which leaves all the anciliaries... It looks (!) simple enough... Emphasize on simple. Is there anything I can seriously damage, besides the cam shaft bearings?
Oh, and I'll order new oil pump gears and pulleys while I'm at it. I'm torn now, either it's DIY (fun, but it will take ages and I'm affarid to break stuff) or a garage (costly, but faster and I have to trust someone to not break stuff).
But hell, I know why the oil cooler thermostat isn't leaking anymore, sand and oil formed a nice seal it seems!
EDIT: I'll open a dedicated thread now, just checked the installation instructions that came with the Kent H200. And man, do I have questions now!
Oh, and I'll order new oil pump gears and pulleys while I'm at it. I'm torn now, either it's DIY (fun, but it will take ages and I'm affarid to break stuff) or a garage (costly, but faster and I have to trust someone to not break stuff).
But hell, I know why the oil cooler thermostat isn't leaking anymore, sand and oil formed a nice seal it seems!
EDIT: I'll open a dedicated thread now, just checked the installation instructions that came with the Kent H200. And man, do I have questions now!
Last edited:
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
How long depends on how rusty things are but you're probably looking at a day to pull it apart and then a day ti reassemble if this is your first time.
Can I quote you on that? ;-) I like your optimism!
EDIT: Things looked reasonably clean earlier, besides the pulleys no visible corrotion anywhere. Not that this means a lot, rotted bolts can be treacherous!
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Maybe I should qualify that that's if things go relatively smoothly. A single bolt can take half a day if it is bad.
