- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Not so much doing as watching MrGorsky change one of his ball-joints. It all went like clockwork with no drama, heat or cold required. Most disappointing.
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 4,653
- Location
- Rotherham
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Never mind Better luck next time
Near-side was more entertaining. The bl**dy press bent out of shape trying to get the new one in. Clearly an Ebay chineesium special. After a lot of mucking about given up and will have to get a replacement. Talk about a throw-away society: lucky if you get 1 car's worth of changing ball-joibts before it is f*cked.
brianp38dse
Well-Known Member
- Posts
- 20,065
- Location
- heathrow
Look on the bright side, even with buying a new tool its still cheaper than getting a garage to do it
RangeRoller dt
Well-Sprung Member
- Posts
- 14,393
- Location
- Trapped inside my head @ LZ asylum
Did you douse it in oil? Trick is get it hydraulicised
RangeRoller dt
Well-Sprung Member
- Posts
- 14,393
- Location
- Trapped inside my head @ LZ asylum
brianp38dse
Well-Known Member
- Posts
- 20,065
- Location
- heathrow
Chances are il make up for that
I have mine to do at some point so one off us will
Gord Wedman
Well-Known Member
- Posts
- 617
- Location
- Chilliwack, British Columbia
The nuts and bolts are not a problem but no one over here is going to be selling that special tool. I don't see any advantage over a thin wall socket and extension anyway.
My brother told me Snap-on has a thin wall impact socket but it's something like US $30.
I will just get them snugged up good with impact and finish with box end wrench.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
I have mine to do at some point so one off us will
He'll be a dab hand at it by then.
Amazing how bad they were. No real sign until you get it apart.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
My old Halfords set works fine but it is easier with the tool.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
I have mine to do at some point so one off us will
This is what you really need with the arms on both sides of the press but it costs 7 times as much!
https://www.island-4x4.co.uk/ball-joint-front-removal-tool-laser-6293-ftc3570-ftc3571-p-37951.html
brianp38dse
Well-Known Member
- Posts
- 20,065
- Location
- heathrow
I have one of these that i got for my vans joints i was hoping it will fit the p38 ones, i can always make up the correct size bit in the workshop.
frog hopper
Well-Known Member
- Posts
- 4,764
- Location
- france
Had a run to the hospital this afternoon, I usually leave 1 1/2 hours before appointment to give 1/2 hour to sort paperwork, and add 1/4 hour onto journey time for the krapton factor. First little town I have to go through has road closed so end up taking a 6 km diversion, so that's the 1/4 hour more or less gone already, hope there are no other problems.
Then I notice the temp gauge hasn't moved off the stop, bummer, carry on with fingers crossed. In reality in 6 years of ownership I have never had a cooling problem, but even so I was glad to get back with no issues. Job for tomorrow - look for disconnected wire from when I changed the filters last week.
It's just unsettling when something like this happens, especially with the VM lump, and it was an appointment I really did not want to miss.
Then I notice the temp gauge hasn't moved off the stop, bummer, carry on with fingers crossed. In reality in 6 years of ownership I have never had a cooling problem, but even so I was glad to get back with no issues. Job for tomorrow - look for disconnected wire from when I changed the filters last week.
It's just unsettling when something like this happens, especially with the VM lump, and it was an appointment I really did not want to miss.
jwrrc
Well-Known Member
- Posts
- 619
- Location
- Warwickshire, UK
Glad you made it there and back without too much issue. At least with an older engine you're only without dials when you leave something off. A modern car would have thrown a right fit and you have been looking for the wire before you could leave!
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
I have one of these that i got for my vans joints i was hoping it will fit the p38 ones, i can always make up the correct size bit in the workshop.
Perfect. We have the right sized spacer things if you need them. In fact, if you want to bring it up round the back of the house we could give you a hand. You might want to paint the brake-disc shield while you have it off.
Thinking about it, I have to come down and pick up Dopey's boot liner at some stage. If MrGorsky is done I could probably drop them off.
Last edited:
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Hope it's a wire off or a duff sensor and not lack of coolant
I got in touch at lunch to be told unfortunately the parts were already with DPD and are on standard shipping. Got an email from DPD telling me I am getting the parts tomorrow. So it sounds like they have upgraded me for free
