- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Rear access?
Yes, that tailgate could do with rotating 6" higher. I have wondered if it could be modified.
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Rear access?
Yes, that tailgate could do with rotating 6" higher. I have wondered if it could be modified.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Advisory or fail? I'd still do them but if the latter I would report the place. Someone not as careful as you will trust them and they'll be a death.
- Posts
- 4,653
- Location
- Rotherham
Attachments
Nothing on the MOT however the specialist has quoted for them to be entirely replaced.
Total bill is £1358 for everything including labour.
Scotiawhiskers
Well-Known Member
- Posts
- 877
- Location
- Manchester
Especially where it had stuck and was about 4" short of fully open.
I suppose actually that should have been a thread called 'What my range rover did to me today' instead of here.
- Posts
- 33,600
- Location
- North Shropshire
Re-evaluating doing the ball joints myself 
if @Flossie offer of the ball joint tool is still there!
Does replacing the CV joint add any difficulty or is that the easy bit?
I know folks say you won't need to centralise the hub if you replace the joints, but the way things have gone on this motor to date, i need to plan for the worst
if @Flossie offer of the ball joint tool is still there! Does replacing the CV joint add any difficulty or is that the easy bit?
I know folks say you won't need to centralise the hub if you replace the joints, but the way things have gone on this motor to date, i need to plan for the worst
Scotiawhiskers
Well-Known Member
- Posts
- 877
- Location
- Manchester
Owt like this. Now that did hurt a bit
Nothing remotely like that. Just feeling the blood trickling through my hair after some Saxon language.
That looks much worse than when I faceplanted into the back of a car who stopped at a green light. More damage to the motorbike from the police walking on it than the actual crash.
- Posts
- 2,427
- Location
- Isle Sheppy
It’s not to bad a job replaced the cv joints on mine why I was at it but I wasn’t in any hurry for the car I will post on here what I’ve done so far one day bloody great long list and big book of invoices to match
Flossie
Well-Known Member
- Posts
- 11,001
- Location
- Shropshire
Yep, no problemRe-evaluating doing the ball joints myself
Does replacing the CV joint add any difficulty or is that the easy bit?
I know folks say you won't need to centralise the hub if you replace the joints, but the way things have gone on this motor to date, i need to plan for the worst
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Holy ****!
Aye.. Not exactly cheap.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Time to get another couple of quotes mate,
Nah, I've worked it out and it's about right. They are a proper specialist too so can't grumble too much!
Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
The CV joint is the easy bit, I posted how to get it off the drive shaft a couple of days ago.Re-evaluating doing the ball joints myself
Does replacing the CV joint add any difficulty or is that the easy bit?
I know folks say you won't need to centralise the hub if you replace the joints, but the way things have gone on this motor to date, i need to plan for the worst
jwrrc
Well-Known Member
- Posts
- 619
- Location
- Warwickshire, UK
It's worth a degree of "extra" payment for a good specialist to know it'll be done right and without damaging your vehicle IMHO
- Posts
- 4,653
- Location
- Rotherham
That was hitting a 4x4 girder frame work headfirst. Quite a few pints of blood came out with that one
Yep and we've come to an agreement we're both happy with, too. Can't fault the chap at all and I'd be happy to buy further cars from him.
Scotiawhiskers
Well-Known Member
- Posts
- 877
- Location
- Manchester
How fast were you going? Reminds me of my mate telling me about being first aider at a truck repair shop. Guy came wandering in covered in blood at the end of tea break and totally confused. He's missed his footing and gone down straight across a truck pit and hit the far side with his face. That was 11am, my mate didn't get back from the hospital until 8pm, to find they'd locked the yard up with his car inside. Guy had broken and dislocated jaw, smashed cheekbone and eye socket, lost a load of teeth, broken nose, plus all the 'ordinary' scrapes, sprains and stuff you'd expect of falling into a deep inspection pit.That was hitting a 4x4 girder frame work headfirst. Quite a few pints of blood came out with that one
- Posts
- 33,600
- Location
- North Shropshire
In other news, brake pedal noise has returned
Different one this time, not had chance to check where it's from
Different one this time, not had chance to check where it's from
- Posts
- 4,653
- Location
- Rotherham
Was down pit riding a conveyor belt (naughty) and electricians had put frame up for transformer I went straight under through the gap, about 12 inches, head first. The steel pins into my head were to hold the front of my face in place until the bone knitted together. Was a bit sore for a while
