Salisbury Nick
Well-Known Member
- Posts
- 790
- Location
- Dorchester
Cheers Grrrrrr, I have not got Rave handy at the moment. is there a bleeding routine I should be following?
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 19,291
- Location
- Buckinghamshire, UK. ('95 DT)
The one in RAVE!
I tend to use a Gunson Easibleed kit to push a load of fresh fluid through the modulator before I start and then just follow RAVE to the letter. Again, I tend to count 10 pumps with no bubbles at all before deciding all air is out. No need to open the bleed nut all the way, just crack it so fluid starts flowing.
Top up the reservoir every time. If it drops too low you'll start all over again.
Salisbury Nick
Well-Known Member
- Posts
- 790
- Location
- Dorchester
Thanks. I’ll consult RAVE and do as you suggest. I still have one ,ore to replace at the rear so i’ll all of it at the weekend.
Salisbury Nick
Well-Known Member
- Posts
- 790
- Location
- Dorchester
- Posts
- 19,291
- Location
- Buckinghamshire, UK. ('95 DT)
Er, Brianp38dse posted them on here. Must have been a few weeks ago now. Possibly in this thread ... Or, now I come to think on it, I may have made a new thread on replacing the brake lines because I was worried others might be going around in death traps.
Tenebreaux
Well-Known Member
- Posts
- 4,290
- Location
- Armagh
Reading this with interest as I'm doing both front calipers this weekend.
- Posts
- 19,291
- Location
- Buckinghamshire, UK. ('95 DT)
- Posts
- 19,291
- Location
- Buckinghamshire, UK. ('95 DT)
A bike inner-tube valve held in the hole where the banjo goes will allow you to pump the pistons out. Put some wood in so they don't pop out completely. Or you can do it on the car before disconnecting the pipe. Just don't go too far!
Be really careful pushing the pistons back in. A little bit of red rubber-grease on the new seals can help. Use fingers/thumbs and ease back, rest, ease a bit, rest until back in all the way. Test afterwards to make sure they move in and out freely before you refit.
Salisbury Nick
Well-Known Member
- Posts
- 790
- Location
- Dorchester
Excellent. Thanks.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,391
- Location
- Trapped inside my head @ LZ asylum
They do take bit of bleeding compared to usual vehicles. Just keep pumping it through, if you get bubbles you are at the right spot. On Manual gearbox clutch also runs off brake fluid reservoir so that may need bleed too (do not squeeze the slave cylinder)
Salisbury Nick
Well-Known Member
- Posts
- 790
- Location
- Dorchester
Nice job. They look great.
Salisbury Nick
Well-Known Member
- Posts
- 790
- Location
- Dorchester
I’d follow @Grrrrrr s advice. I did not do any of that and now I need to back do it properly!
RangeRoller dt
Well-Sprung Member
- Posts
- 14,391
- Location
- Trapped inside my head @ LZ asylum
He is Grr?
- Posts
- 19,291
- Location
- Buckinghamshire, UK. ('95 DT)
Why's dat den?!
- Posts
- 19,291
- Location
- Buckinghamshire, UK. ('95 DT)
Brian's work. He's a legend with those pipes. I am very grateful he popped up to help.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,391
- Location
- Trapped inside my head @ LZ asylum
Because when your clutch pedal hits the floor, and your LandyZone mate finds it of no consequence anyway, you may lose your job for not turning up next day.
Is why.
- Posts
- 19,291
- Location
- Buckinghamshire, UK. ('95 DT)
This car has been standing for a while?
she does about 2000 miles a year, mainly while I'm fixing the Jeep!
Datatek
Well-Known Member
- Posts
- 44,853
- Location
- Near Poitiers SW France
Play day fixing broken bits of plastic, replaced the tailgate seal with the one from my scrapper after cleaning it and cleaning the the metal work. Found that the water leak is due to water getting into the seal mounting groove at the top and running down inside the seal into the spare wheel well.
Replaced the aircon belt and now have the aircon working again,just in time as it got close to 30C today
Replaced the aircon belt and now have the aircon working again,just in time as it got close to 30C today
