What's with the broken tennis bat
if you are really lucky you get a spare in with the spare wheel too
J
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
if you are really lucky you get a spare in with the spare wheel too
J
- Posts
- 12,609
- Location
- Sud ouest France !
I have a UME sensor on my 38'
- Posts
- 12,609
- Location
- Sud ouest France !
You mean ones fallen off?if you are really lucky you get a spare in with the spare wheel too
J
Datatek
Well-Known Member
- Posts
- 44,846
- Location
- Near Poitiers SW France
Captive washers are a production aid, can't be frigging around putting washers on bolts on the production line.
stuu
Well-Known Member
- Posts
- 1,943
- Location
- Aberdeenshire
Fold in over 70mph help with fuel economy
And, probably cheaper than flanged bolts.
stuu
Well-Known Member
- Posts
- 1,943
- Location
- Aberdeenshire
Busy day
New toe arms bolts and nuts and eccentric washers
New rear hub upper and lower rose joints with bolts nuts and eccentric washers,
New rear wheel bearings
New backing plates
New handbrake shoes and fitting kit it works really really well now,
Front tie rods freed for alignment tomorrow,
Rear air springs was done on this motor in 2020 and they have contitech then the land rover logo below are these likley genuine or cheepos?
Front struts was done in 2019 and have the landrover sticker and barcode/partnumber sticker on i can't find that on the rear air springs though
New toe arms bolts and nuts and eccentric washers
New rear hub upper and lower rose joints with bolts nuts and eccentric washers,
New rear wheel bearings
New backing plates
New handbrake shoes and fitting kit it works really really well now,
Front tie rods freed for alignment tomorrow,
Rear air springs was done on this motor in 2020 and they have contitech then the land rover logo below are these likley genuine or cheepos?
Front struts was done in 2019 and have the landrover sticker and barcode/partnumber sticker on i can't find that on the rear air springs though
- Posts
- 33,445
- Location
- North Shropshire
Summink has changed!!
Just filled up with more diseased fool.. brim to brim, 28mpg, dash said 31 mpg!! That's a lot closer and i can live with that!!!
No idea what's changed
Just filled up with more diseased fool.. brim to brim, 28mpg, dash said 31 mpg!! That's a lot closer and i can live with that!!!
No idea what's changed
Datatek
Well-Known Member
- Posts
- 44,846
- Location
- Near Poitiers SW France
If you don't reset the computer each time you fill up, it's probably just adapting the average to your driving style.
- Posts
- 33,445
- Location
- North Shropshire
i reset the trip, which resets the average MPG-ometer
theres 3 trips, one i reset on each tank, one i never reset, the other auto-resets at each ignition cycle
Datatek
Well-Known Member
- Posts
- 44,846
- Location
- Near Poitiers SW France
In that case, it's just the standard LR inaccuracy
rich28uk
Well-Known Member
- Posts
- 635
- Location
- Manchester
Same as my td6, rear have contitech and LR logo, don’t know if genuine or LR approved parts etc but I have an old invoice for rear bags done at a LR dealer so I’d imagine genuine, seem decent though.
rich28uk
Well-Known Member
- Posts
- 635
- Location
- Manchester
Took advantage of fine weather and got lower hub bushes/ rose joints changed, very easy with a push pull tool, hardest bit was removing the big circlip, even the bolts came out in good condition.
Front track rod ends to do over weekend than find somewhere that can do 4 wheel alignment.
Front track rod ends to do over weekend than find somewhere that can do 4 wheel alignment.
1988smithy
Well-Known Member
- Posts
- 4,042
- Location
- West midlands
Same as my tdv8
1988smithy
Well-Known Member
- Posts
- 4,042
- Location
- West midlands
My rear offside were advisories on last MOT, what puller did you use, one of those 200 quid jobbies?
frog hopper
Well-Known Member
- Posts
- 4,758
- Location
- france
Could it be a sensor counting the bits that fall orf?
1988smithy
Well-Known Member
- Posts
- 4,042
- Location
- West midlands
Yeah but the sensor fell orf
rich28uk
Well-Known Member
- Posts
- 635
- Location
- Manchester
Universal Press & Pull Sleeve Kit Insert Installation Bush Bearing Removal Tool | eBay
27 Pcs Universal Press & Pull Sleeve Kit Bush Bearing Removal Insertion Tool Set. This complete wheel bearing set includes 22 sleeves, and 5 sizes of pulling spindles (M10 / M12 / M14 / M16 / M18).
www.ebay.co.uk
rich28uk
Well-Known Member
- Posts
- 635
- Location
- Manchester
I am considering buying one and making an adapter to fit in my flypress. Then I can use it in situ with the threaded bars and in press for bearing pushing etc.This is a copy of it, one I used iv borrowed of a mechanic I know, the link above is a direct copy of it, albeit unknown brand, made life very easy, once it starts to move it comes out easy and new one in easy.Universal Press & Pull Sleeve Kit Insert Installation Bush Bearing Removal Tool | eBay
27 Pcs Universal Press & Pull Sleeve Kit Bush Bearing Removal Insertion Tool Set. This complete wheel bearing set includes 22 sleeves, and 5 sizes of pulling spindles (M10 / M12 / M14 / M16 / M18).www.ebay.co.uk
- Posts
- 19,287
- Location
- Buckinghamshire, UK. ('95 DT)
Contitech should be pretty decent.
