What did you do with your Range Rover today

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
kermit_rr said:
i dont want to go very far at all, I'll be happy to just change the big end shells if thats what it turns out to be. I really dont want to lump the engine out, but if needs must etc
Click to expand...
I carried out this proceedure years ago on one of my Granada 2.8 engines. Worked a treat and she ran perfectly for another 2 years until i sold her so its deffo worth a punt. I did mine one at a time too and marked the end cap with tippex to remind me i had done that one between tea breaks. LOL
 
The car has started sagging at the rear so I had a look could not see or hear any leak so I have isolated the rears from the block, I did not have any emergency valves so I made up my own, handy when you have kids with bikes and old inner tubes the valves are 6mm under the rubber,
20210330_140014.jpg
I had one screw in valve that will do 8mm
 
Wire brushed and flooded all the nuts around the front turrets and shocks with plus gas ready for removal in a few days time.
I had decided a couple of months ago that I was going to change the shocks after noticing that the top bushes on both were starting to break up, but I have been a bit ill of late so haven't got round to it. When I got underneath to wire brush the bottom mounts, both shocks were as loose as feck, just hope the axle mount brackets arn't too warn or I will be into welding new holes, and I would rather not do that at the moment.:(:(:(
 
frog hopper said:
Wire brushed and flooded all the nuts around the front turrets and shocks with plus gas ready for removal in a few days time.
I had decided a couple of months ago that I was going to change the shocks after noticing that the top bushes on both were starting to break up, but I have been a bit ill of late so haven't got round to it. When I got underneath to wire brush the bottom mounts, both shocks were as loose as feck, just hope the axle mount brackets arn't too warn or I will be into welding new holes, and I would rather not do that at the moment.:(:(:(
Click to expand...
If we go into full lock down, you'll all the time in the world matey!! :oops:
 
What did I do with my Range Rover today. Took it on the ferry and went to Bisley and shot 100 clays, well shot at 100 clays and hit about 70 of them.....she looked a treat in the car park next to 70 plate motors! Anyone else shoot clay?
 
What a day. Had a run round in the Rangie this morning then went shopping> Pulled into Tesco tried to wind up window, clank then dropped about 1/2 inch when got to the close position. Managed to wedge up:eek::eek:
Afternoon took MX5 for a run 30 miles round outskirts of Sheffield no trouble. Heading home came to a junction at on of Sheffield's busiest roads and needed to right turn. Eventually gap appears foot down halfway across. Nothing dead as a doornail. No hazards no nothing. For some reason + terminal chose that moment to come off. All tools in RR so once again bit of wedging needed to get home. What was happening today?:eek::eek:
 
Rubberknees said:
What a day. Had a run round in the Rangie this morning then went shopping> Pulled into Tesco tried to wind up window, clank then dropped about 1/2 inch when got to the close position. Managed to wedge up:eek::eek:
Afternoon took MX5 for a run 30 miles round outskirts of Sheffield no trouble. Heading home came to a junction at on of Sheffield's busiest roads and needed to right turn. Eventually gap appears foot down halfway across. Nothing dead as a doornail. No hazards no nothing. For some reason + terminal chose that moment to come off. All tools in RR so once again bit of wedging needed to get home. What was happening today?:eek::eek:
Click to expand...
Wedgie day :eek:
 
Rubberknees said:
What a day. Had a run round in the Rangie this morning then went shopping> Pulled into Tesco tried to wind up window, clank then dropped about 1/2 inch when got to the close position. Managed to wedge up:eek::eek:
Afternoon took MX5 for a run 30 miles round outskirts of Sheffield no trouble. Heading home came to a junction at on of Sheffield's busiest roads and needed to right turn. Eventually gap appears foot down halfway across. Nothing dead as a doornail. No hazards no nothing. For some reason + terminal chose that moment to come off. All tools in RR so once again bit of wedging needed to get home. What was happening today?:eek::eek:
Click to expand...

Guessing teeth gone on end of regulator. Common problem but normally preceded with grinding at the top of the movement before it goes completely. I guess someone could have already replaced it and used bolts rather than rivets and one has come undone.
 
Grrrrrr said:
Guessing teeth gone on end of regulator. Common problem but normally preceded with grinding at the top of the movement before it goes completely. I guess someone could have already replaced it and used bolts rather than rivets and one has come undone.
Click to expand...
If I hold the glass it winds up and down OK. it's as if a runner has come loose. As soon as weather picks up will investigate.
 
Developed a nice steering shudder under braking recently, very bad if I accelerate then immediately stomp on the brakes, the wheel shakes badly.
There is also a nice pulsation through the brake pedal when braking, oh what fun. :rolleyes:

Oh and the weird bit if I brake very gently from say 70 it's fine until I reach around 35mph and she starts to shimmy and pulsate. grr!!!
 
You must log in or register to reply here.

Similar threads

A
Range Rover L322 - not turning over
Replies
12
Views
1K
gold rover
gold rover
B
L320 range rover sport 3.0 tdv6 loosing power steering fluid
Replies
3
Views
494
Mark Piercy
Mark Piercy
F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
1K
Grrrrrr
Grrrrrr
T
Non start
Replies
3
Views
712
Datatek
Datatek
T
Fan Clutch??
Replies
14
Views
790
Grrrrrr
Grrrrrr
Back
Top