well needed restoration of my series 2a

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Im really liking this thread, Making me want to dash out and get another rust bucket to re-build!:rolleyes:.
Ill be interested to see your next installment! Keep up the good work!
 
Jackual_NZ said:
Im really liking this thread, Making me want to dash out and get another rust bucket to re-build!:rolleyes:.
Ill be interested to see your next installment! Keep up the good work!
Click to expand...


cheers, should be all going back together in the next few weeks, plenty of pics to come, then its bulkhead restoration time.;)
 
right, after rewiring me trailer and replacing the back lights on me 90, i got a bit done this afternoon ,

had to get the sleves out fer the cam followers

DSC00204.jpg


as i wernt happy with them ( after all this) ah well ther done now, i had to make a puller for it out of a bolt ! easy really ( cheaper than a slide hammer too)

DSC00205.jpg


then i put all the timimg gears back on and set up the timing , sorry no photos of the process !

DSC00202.jpg


looks more like an engine again now

dropped in the oil pump gears and bits fer the dizzy

DSC00201.jpg


got fuel pump and oil filler tube ready fer fitting , along with timimg case, more pics to come tomorrow,
 
so , today i got the timimg case on, glued gaskit on one side and grease on the engine side incase it ever has to come off ,

DSC00207.jpg


DSC00208.jpg


then cleaned the head off with thinners ready for the gaskit,

DSC00206.jpg


i went and picked up a composit fiber gaskit with the stainless rings on

fitted it dry , then torqed the head up in two stages from hand tight, one at 30 then the second run at 65,

DSC00209.jpg


DSC00210.jpg


DSC00211.jpg


oh yeah dropped the push rods in before hand ( edit in somewhere above )

DSC00212.jpg


then set the tappits up,

DSC00215.jpg


with valve no 8 fully open i set valve no1 to 0.010 with the feelers then locked the adjuster, then followed on in this order

valve 8- adjust no1
valve 6-3
valve 4-5
valve 7-2
valve 1-8
valve 3-6
valve 5-5
valve 2-7

easy as that !

dropped a few more bits on,

DSC00216.jpg


DSC00217.jpg


DSC00218.jpg


looking more like it now, just need to find a better oil filter and sort me fuel pump out !
 
stuck the sump on with hylomar non setting instant gaskit eitherside of the paper gaskit,

DSC00213.jpg


then sorted the dynamo out i reconditioned months ago,

DSC00214.jpg
 
yeah , am un decided if the dizzy is buggered or not , so need to make a test circuit up tomorrow then will decide weather to keep it or swap it over, then will spray it ;)
 
ah could do it tomorrow, :) after a mornings finishing off , but want to get the new chassis / old chassis restored before it gets dropped in , will prob fire it up in a stand so i can get it running smooth, in the next couple of weeks, no rush , got a few bits to sort out , starter motor, bell housing , timimg , fuel pump, pullys belts etc, oil filter, nothing major, just bits
 
will keep boring you all with the pics, got the rest to do now, think il do the quick gear box overhall, then the bulkhead restoration ( rotted to ****) but am going to repair it all ! slowly but surely.
 
You must log in or register to reply here.

Similar threads

N
Series 2a 69/70 wiring mess
Replies
7
Views
554
grewth
G
G
Brake servo on a 2A Diesel ?
Replies
11
Views
710
grewth
G
D
Series 2a with a Suffix F gearbox. Full Synchro?
Replies
5
Views
1K
cornish rattler
cornish rattler
Frisol
Series 2a Compliance Check and Warrant of Fittness
Replies
13
Views
2K
Huntforalandy
H
R
Steel hardtops.
Replies
5
Views
891
rubix101
R
Back
Top