P38A Water ingress causing damp / condensation and mould spots

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.

awkwardbob

Well-Known Member
Posts
578
Location
Glasgow
Hi,

apologies for second post this morning.
I’ve grown to love our ‘97 P38 and have been able to deal with a lot of her foibles.
The one I’m having most angst with, however, is that she’s, well, damp.
Soaking.
If I open the rear doors, there’s water under where the door was closed.
the front carpets seem damp too.
I’ve had water drip on my feet whilst driving.

it does seem to be rainwater / exterior moisture getting in rather than any fluid or heater leaks but it’s driving me nuts and I’m starting to see damp / mould patches appearing.

where are the likely culprits for water ingress, what should I be looking out for and how can I stop the sogginess ?

very very grateful for any help and advice on this one.

Bob
 
Sorry, wasn’t trying to be offensive, apologies for any caused.
Will change it if I can work out how to
 
Pollen filters or scuttle, seal round pollen filter housing with self adhesive draft excluder then replace covers, scuttle drains are a bit more involved you have to take of all the trim and seal round all the screws and make sure all the drains are clear.

a quick copy and paste from a previous thread:D
 
Last edited:
On YouTube there is a video showing removal of all the panels below the wiper arms to reseal them. If sealing the pollen filters does not solve your problem that procedure would be the next step. I have done this and still have wet carpets so must revisit the problem.
In an earlier car, a 98, I discovered a leak at the seam where the door frame joins the roof. This caused the headliner by the sun visor to get wet. I wonder if this could drain all the way to the floor? The headliner in my 99 is not wet so I doubt this is my problem. If I ever fix the leak I will post. The source. Good luck.
PS: you might leave a couple windows open a crack to reduce humidity and mold buildup.
 
On YouTube there is a video showing removal of all the panels below the wiper arms to reseal them. If sealing the pollen filters does not solve your problem that procedure would be the next step. I have done this and still have wet carpets so must revisit the problem.
In an earlier car, a 98, I discovered a leak at the seam where the door frame joins the roof. This caused the headliner by the sun visor to get wet. I wonder if this could drain all the way to the floor? The headliner in my 99 is not wet so I doubt this is my problem. If I ever fix the leak I will post. The source. Good luck.
PS: you might leave a couple windows open a crack to reduce humidity and mold buildup.
And always have your A/C on.
 
Thanks All,

I have had a look through before and have investigated the pollen filter covers which seem fine.
I’ll try and find that video and look
Through race to see how best to delve a little deeper.
I’ve the centre console out just now as I was sorting the hevac screen and replacing a few blown bubbles and the glovebox and cubby struts.
It might just be trial and error with a hose !

but thanks for the pointers.

Bob

-had cracked the windows and sunroof all day to let her breathe a bit. Unfortunately I’m need to replace the AC condenser and drier which I might attempt next week if I’m feeling brave !
 
Take the door cards off & see if the plastic weather sheets are present, in good condition & securely glued (or masticed) to the metal of the doors.
Water runs down the outside of the door glass & a lot of it passes the rubber waist seals & drips off the bottom of the window into the door.
The plastic sheets keep it in the door & it exits via the drain holes in the bottom of the doors - check they're clear.
Otherwise it can drip onto & run down the back of the door card & into the car
May not be your problem but it's a common issue - not just with LRs - & causes much headscratching.
Any plastic sheet will do & butyl rubber strip - basically very sticky plasticine - does a good job of sticking it on.
E.g: https://www.ebay.co.uk/itm/4M-Butyl...dlight-LED-Retrofit-Reseal-Strip/265105166135
 
Thanks guys,

the weather sheets are present but have been brutalised by a PO so I may look at trying to repair / replace those.
Will check the drain holes too.
Boot is like a swimming pool with no obvious signs of where the water is coming from !

all part of the fun I suppose !

will take some pics and report back

Thanks again

Bob
 
If you dry the boot out then give it a light dusting of talc powder you will be able to track where its running from:D
 
The drips on yer driving foot and passenger side wet spots on mat, are from the top part of the pollen filter housing, the bit you can't reach with weatherproof sealant. It's worse if you remove the filter. The boot is usually a bad rubber seal if you park on a slant., Remove boot rubber, black sealant all round metal and bosh rubber back on before sealant dries. This seals inside of ribber and lifts it making a better seal, also tighten your back door up for good measure.
It's an age thing.
 
Well today I stripped down the front end and found water in my pollen filters, so at least that’s somewhere there’s been a problem.

Evidence of past issues too and some remedial work possibly on passenger side.

stripped back, cleaned up. Small bead of silicon between rubber gasket and plastic filter housing, then again in the underside of the metal panel which seals to the body work.
Hoping that will have helped, will keep
An eye on it though !
 

Attachments

  • 8DFFED57-A958-4D50-8DF8-D035E8AD77FF.jpeg
    8DFFED57-A958-4D50-8DF8-D035E8AD77FF.jpeg
    349.4 KB · Views: 93
  • 215821E5-802C-42A2-9781-7D2055226FF5.jpeg
    215821E5-802C-42A2-9781-7D2055226FF5.jpeg
    431.4 KB · Views: 100
Well today I stripped down the front end and found water in my pollen filters, so at least that’s somewhere there’s been a problem.

Evidence of past issues too and some remedial work possibly on passenger side.

stripped back, cleaned up. Small bead of silicon between rubber gasket and plastic filter housing, then again in the underside of the metal panel which seals to the body work.
Hoping that will have helped, will keep
An eye on it though !
Put some draught excluder around the pollen filter lid as well when you put it back together.every little helps.
 
Back
Top