Michalis Karatzis
Active Member
- Posts
- 189
- Location
- Cyprus
So I connected a boost gauge as you can see in the photo. When I see a sustained 225-227kPa on the Nanocom the gauge shows 240kPa.
Disco 2 Wastegate strange behaviour
- Thread starter Michalis Karatzis
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
So I connected a boost gauge as you can see in the photo. When I see a sustained 225-227kPa on the Nanocom the gauge shows 240kPa.
sierrafery
Well-Known Member
- Posts
- 17,910
- Location
- Arad/Romania
No photo in your post but if you tapped into the inlet and you trust your gauge you need a new genuine MAP sensor or if that's ruled out as well the problem is with the fuel map
Michalis Karatzis
Active Member
- Posts
- 189
- Location
- Cyprus
I tried another MAP from another TD5 and it showed exactly the same figures on the Nanocom. So I guess the fuel map is suspect.
Attachments
Last edited:
- Posts
- 5,583
- Location
- Surrey / Hants border
Can you borrow an ECU with a standard map to rule out yours being fiddled with?
Michalis Karatzis
Active Member
- Posts
- 189
- Location
- Cyprus
That is an option but I don't want to mess up with another person's ecu
- Posts
- 5,583
- Location
- Surrey / Hants border
I was going to suggest getting a used one from ebay but just had a look to see how much they are.....
.Forget that idea!
Michalis Karatzis
Active Member
- Posts
- 189
- Location
- Cyprus
I was planning to get a remap but before that I wanted to sort this issue out. Maybe I should go ahead with the remap and hope that it will solve the problem.
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
That's a bit like burying your head in the sand.
Michalis Karatzis
Active Member
- Posts
- 189
- Location
- Cyprus
That's a bit like burying your head in the sand.
Wishful thinking...
- Posts
- 5,583
- Location
- Surrey / Hants border
I can see the logic there - if the map is corrupt or just plain wrong, a remap should correct it, but I would put the actuator etc back to standard first.That's a bit like burying your head in the sand.
But you're right, it's still a gamble!
sierrafery
Well-Known Member
- Posts
- 17,910
- Location
- Arad/Romania
As log as the gauge is accurate, there are no leaks and with how the wastegate is tightened to max it means that there's no wasted pressure and that 240Kpa is all the pressure you get so i see two scenarios: the turbo has a problem and can't deliver more no matter how fast it spins or the engine is underfuelled.... a normally working td5 even on stock fuel map should go to overboost with closed wastegate at max 3000 rpm under load that's a fact
Michalis Karatzis
Active Member
- Posts
- 189
- Location
- Cyprus
I can't guarantee the accuracy of the gauge but let's say I trust it. The same gauge showed a max of ~255-260kPa before the intercooler when I connected it to the line going to the modulator. The turbo was visually checked and blades/bearing looked healthy. The only thing I have no way to check is the fuel map. I wanted to get a remap from Storm Tuning for some time now but first I needed to figure out what is the issue at hand. Maybe I should go ahead and see if it solves the issue.
- Posts
- 45,057
- Location
- East Dorset
Wonder if an LR or other 4x4 garage near you has a standard ECU they could plug in, set to your vehicle then test it. That would eliminate it if the problem is still there.
Or maybe they could read your map and tell you if it is standard.
Me no expert, but it seems a commonsense thing to do.
Or maybe they could read your map and tell you if it is standard.
Me no expert, but it seems a commonsense thing to do.
sierrafery
Well-Known Member
- Posts
- 17,910
- Location
- Arad/Romania
Long thread so i dont remember but if it's MSB ECU not NNN the map is not visible via OBD port only if the chip is removed and inserted into a chip reader
- Posts
- 45,057
- Location
- East Dorset
Told you I was no expert on electrics! But still, a garage might have a standard replacement ECU they use for elimination purposes, if not i would wonder why!
Alpinejim
Active Member
- Posts
- 242
- Location
- Sunny Suffolk
I have a 10p ECU if you want to try it.
Michalis Karatzis
Active Member
- Posts
- 189
- Location
- Cyprus
Thank you for your offer but I will probably get a remap on my existing ecu.
Little art
Active Member
- Posts
- 119
- Location
- Nijmegen
Michaelis, as i am stil underpowered as wel I follow this thread. Does you’re car has an exhaust filter?
My egr was blanket just before the car was sold to us don’t know the history but it was driven short blocks round because the exhaust filter was jammed with clutter.
There should be more power somewhere but now it drives like a normal car even up hill top speed is only 130kmh could be doing more I think.
Good luck on the search! & grtzz
My egr was blanket just before the car was sold to us don’t know the history but it was driven short blocks round because the exhaust filter was jammed with clutter.
There should be more power somewhere but now it drives like a normal car even up hill top speed is only 130kmh could be doing more I think.
Good luck on the search! & grtzz
